Electrolux P6000 (Nexus) Series Скачать руководство пользователя страница 98

Страница: 98 / 118

SOI/DT 2002-05 eb

599 35 23-17

9.2 Control panel (standard version)

9.2.1 Control panel – versions for “soft” cabinet

a.  Remove the work-top
b.  Extract the detergent drawer (8)
c.  Remove the screws that secure the control panel to the control panel

support (9)

d. For models with knobs external to the control panel: release the knob

cover by pressing the hole gently with a small screwdriver and turning
the knob cover counter-clockwise (10)

e. Remove the screws which secure the control panel to the cross-

member and release the anchor tabs from the support (12)

f. Release the control panel from the lower right-hand guide and

remove. To facilitate its release, unscrew the screw which secures it
to the cabinet and lift the control panel support slightly (13 or 14).

g. Remove the pilot lamp from its housing in the control panel and (for

electronic models) disconnect the wiring connectors from the PCB.

When re-assembling

: Ensure that the knobs/flanges are positioned

correctly!

9.2.2 Control panel – versions for “square” cabinets

a.  Remove the work-top
b.  Extract the detergent drawer (8)
c.  Remove the screws which secure the control panel to the control

panel support (9)

d. For models on which the knobs are external to the control panel:

release the knob cover by pressing the hole gently with a small
screwdriver and turning the knob cover counter-clockwise (10-11)

e. Remove the front-mounted screws which secure the control panel

support to the cabinet (13 or 14) and, if present, those that secure the
control panel (12).

f. If present, remove the internal screw that secures the control panel to

the support.

g. Release the tabs which anchor the control panel to the support (15-

16) and remove the control panel. To facilitate this operation, lift the
support to release the lower anchor tabs on the control panel (17).

h. Remove the pilot lamp from its housing in the control panel and (for

electronic models) disconnect the wiring connectors from the PCB.

When re-assembling

: Ensure that the knobs/flanges are positioned

correctly!

Содержание P6000 (Nexus) Series























































































































Результаты поиска

Содержание P6000 (Nexus) Series

Отзывы:

Бренды по названию

Популярные бренды

Electrolux P6000 (Nexus) Series, Руководство по обслуживанию

Результаты поиска

Содержание P6000 (Nexus) Series

Отзывы:

Бренды по названию

Популярные бренды