Electrolux P6000 (Nexus) Series Скачать руководство пользователя страница 106

Страница: 106 / 118

SOI/DT 2002-05 eb

106

599 35 23-17

9.6 Washing group (Carboran-inox)

a. Remove the fixing ring and detach the bellows seal from the

front panel

b.  Remove the rear shell
c.  Remove the clamps from the tub suspension springs (53)
d.  Detach the various hoses from the tub (dispenser-tub,

steam venting hose, tub-manifold etc.)

e. Remove all the wiring connectors from the components

fastened to the tub (motor, heating element, thermostats)
and, if present, the bulb of the adjustable thermostat

f. Remove the motor to lighten the tub
g. Remove the fixing screws and remove the rear

counterweight (only if featured)

h. Remove the two pins which secure the dampers to the tub
i. Lay the appliance face down (on a sheet of polystyrene or

cardboard to prevent scratching the cabinet)

j. Use a piece of string or wire to detach the tub suspension

springs from the cross-member

k. Remove the tub from the appliance

9.7 Drum and tub shells (Carboran)

a.  Remove the drum pulley and the motor
b.  Remove the tub from the appliance
c.  Remove the screws which secure the two shells together
d.  Remove the drum

Re-assembly

: It is advisable to replace the sealing ring between the two tub shells whenever the tub is

opened. Connect the hoses to the tub in the correct positions.

9.7.1 Drum shaft bearings

If it is necessary to replace the bearings, the engineer may:

replace the rear tub shell complete with bearings and sealing ring

replace the bearings and the sealing ring only

In the latter case:
a. Remove the tub and the drum from the appliance
b. First remove the external bearing, then the internal bearing with its seal

When re-assembling

In order to prevent damage to the bearing and the seal during re-assembly,
use spacers of the appropriate diameter

Pack the bearings with the specific grease all around the sealing ring (55).

Check that the drum shaft bushing is undamaged, otherwise replace the
drum spider or the drum itself.

9.7.2 Drum

spider

a. Remove the screws which secure the spider to the drum
b. Use two narrow chisels to remove the spider from the drum band

When re-assembling:

Replace the spider on the drum ensuring that the fixing holes are correctly aligned

Insert the spider into the seat in the drum band and, if necessary, rotate it until the holes are correctly
aligned

If the same screws are used, clean and apply thread fixing paste

Tighten the screws securely

Содержание P6000 (Nexus) Series























































































































Результаты поиска

Содержание P6000 (Nexus) Series

Отзывы:

Бренды по названию

Популярные бренды

Electrolux P6000 (Nexus) Series, Руководство по обслуживанию

Результаты поиска

Содержание P6000 (Nexus) Series

Отзывы:

Бренды по названию

Популярные бренды