Electrolux P6000 (Nexus) Series Скачать руководство пользователя страница 114

Страница: 114 / 118

SOI/DT 2002-05 eb

114

599 35 23-17

9.12 Access to specific washer-dryer components

9.12.1 Bellows seal and drying duct

a.  Remove the work-top
b.  Remove the screw which secures the duct to the tank (80)
c.  Open the porthole door, remove the screw which secures the

duct to the cabinet, detach the duct from the heating element
casing and pull the seal downwards (81)

d. Detach the seal from the front panel
e. Detach the circulation hose from the seal (Jetsystem models

only) (78)

f. Remove the wire clamp which secures the seal to the duct and

remove the seal (82)

At this point, the duct can be accessed. To access the seal,
proceed as follows:

g. Remove the seal and the ring by pulling downwards

Re-assembly

Use soap and water to lubricate the seal seat where it comes
into contact with the flange and the metal ring

Replace the seal, ensuring that the reference mark on the seal
is aligned with the hole for the screw which secures the duct to
the front panel (83)

Re-connect the circulation hose (if featured) with the hose
clamp (79)

When replacing the wire hose clamp, ensure that it is correctly
positioned in the groove in the seal, then proceed as shown in
the figure (84)

Lubricate the seal with soap and water to facilitate insertion of
the duct into the heating element casing.

Use pliers to re-close the two anchor tabs and tighten the
screw (85)

Attach the seal to the front panel

Re-tighten the screw which secures the duct to the cabinet

Replace the ring which secures the duct to the cabinet using
pliers to close in position

After fitting a new bellows seal, lubricate the external surface
(which comes into contact with the porthole door) with
silicone oil. This will ensure that the porthole door does not
stick to the seal during the first few drying cycles.

Содержание P6000 (Nexus) Series























































































































Результаты поиска

Содержание P6000 (Nexus) Series

Отзывы:

Бренды по названию

Популярные бренды

Electrolux P6000 (Nexus) Series, Руководство по обслуживанию

Результаты поиска

Содержание P6000 (Nexus) Series

Отзывы:

Бренды по названию

Популярные бренды