Electrolux E30MO65GSSB Скачать руководство пользователя | Manualshive

Страница: 7 / 64

background image

Basic Information

1-5

Before Servicing

1. Disconnect the power supply cord, and then remove
outer

case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

Whenever troubleshooting is performed, the power
supply must be disconnected. It may, in some cases, be
necessary to connect the power supply after the outer
case has been removed, in this event:

1. Disconnect the oven power supply cord and then

remove the outer case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect leads to the primary of the inverter unit.

5. Ensure that these leads remain isolated from other

components and oven chassis by using insulation

tape.

6. After that procedure, reconnect the power supply

cord.

When Testing Is Completed

1. Disconnect the power supply cord, and then remove
outer

case.

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Reconnect leads to the primary of the inverter unit.

5. Reinstall the outer case (cabinet).

6. Reconnect the power supply cord after the outer

case is installed.

7. Run the oven and check all functions.

After repairing

1. Reconnect all leads removed from components

during

testing.

2. Reinstall the outer case (cabinet).

3. Reconnect the power supply cord after the outer

case is installed.

4. Run the oven and check all functions.

Microwave ovens should not be run empty. To test

for the presence of microwave energy within a cavity,

place a cup of cold water on the oven turntable, close

the door and set the power to HIGH and then set the

microwave timer for two (2) minutes. When the two

minutes has elapsed (timer at zero) carefully check

that the water is now hot. If the water remains cold

carry out Before Servicing procedure and re-examine

the connections to the component being tested.

MICROWAVE OVENS CONTAIN CIRCUITRY CAPABLE OF PRODUCING
VERY HIGH VOLTAGE AND CURRENT. CONTACT WITH THE
FOLLOWING PARTS MAY RESULT IN A SEVERE, POSSIBLY FATAL,
ELECTRICAL SHOCK.

INVERTER UNIT, THAT INCLUDES HIGH VOLTAGE CAPACITOR,
HIGH VOLTAGE POWER TRANSFORMER, HIGH VOLTAGE RECTIFIER,
HEAT SINK ETC., AND MAGNETRON, HIGH VOLTAGE HARNESS ETC..
READ THE SERVICE MANUAL CAREFULLY AND FOLLOW ALL
INSTRUCTIONS.

Don't Touch !
Danger High Voltage

To discharge the high voltage capacitor, wait for 60
seconds and then short-circuit the connection of
the high-voltage capacitor (that is the connecting
lead of the high-voltage rectifier) against the
chassis with the use of an insulated screwdriver.

To discharge the high voltage capacitor, wait for 60
seconds and then short-circuit the connection of
the high-voltage capacitor (that is the connecting
lead of the high-voltage rectifier) against the
chassis with the use of an insulated screwdriver.

«
...
5
6
7
8
9
...
»

Содержание E30MO65GSSB

































































Отзывы:

Нет отзывов

Похожие инструкции для E30MO65GSSB

Бренд: Jenn-Air Страницы: 4

B6ACH7H 0B Series

Бренд: NEFF Страницы: 40

Бренд: NEFF Страницы: 48

Бренд: NEFF Страницы: 36

Бренд: NEFF Страницы: 152

Бренд: NEFF Страницы: 40

Бренд: NEFF Страницы: 52

Бренд: NEFF Страницы: 56

Бренд: NEFF Страницы: 56

Бренд: NEFF Страницы: 60

Бренд: NEFF Страницы: 44

Profile Advantium PSA2200R

Бренд: GE Страницы: 80

Profile Advantium PSB9240DFBB

Бренд: GE Страницы: 3

Бренд: GE Страницы: 40

Бренд: Atag Страницы: 76

Бренд: Omega Страницы: 20

Бренд: Daewoo Страницы: 39

Spacemaker JVM1540DMBB

Бренд: GE Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды