Electrolux E30MO65GSSB Скачать руководство пользователя | Manualshive

Страница: 35 / 64

background image

Troubleshooting and Testing

3-11

Procedure

Letter

P

Component Test

TOUCH CONTROL PANEL ASSEMBLY TEST

The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc.
Therefore, unlike conventional microwave ovens, proper maintenance cannot be performed with
only a voltmeter and ohmmeter. In this service manual, the touch control panel assembly is divided
into two units, Control Unit and Key Unit, and also the Control Unit is divided into two units, LSI Unit
and Power Unit, and troubleshooting by unit replacement is described according to the symptoms
indicated.

Before testing,

1.   Disconnect the power supply cord, and then remove outer case.
2.   Open the door and block it open.
3.   Discharge high voltage capacitor.
4.   Disconnect the leads to the primary of the power transformer.
5.   Ensure that these leads remain isolated from other components and oven chassis by using
insulation

tape.

6. After that procedure, re-connect the power supply cord.

1. Key Unit.

1.   Disconnect the power supply cord, and then remove outer case.
2.   Open the door and block it open.
3.   Discharge high voltage capacitor.
4.   Check Key unit ribbon connection before replacement.
5.   Reconnect all leads removed from components during testing.
6.   Re-install the outer case (cabinet).
7.   Reconnect the power supply cord after the outer case is installed.
8.   Run the oven and check all functions.

The following symptoms indicate a defective key unit.

a) When touching the pads, a certain pad produces no signal at all.

b) When touching a number pad, two figures or more are displayed.

c) When touching the pads, sometimes a pad produces no signal.

If the Key unit is defective.

1.   Disconnect the power supply cord, and then remove outer case.
2.   Open the door and block it open.
3.   Discharge high voltage capacitor.
4.   Replace the Key unit.
5.   Reconnect all leads removed from components during testing.
6.   Re-install the outer case (cabinet).
7.   Reconnect the power supply cord after the outer case is installed.
8.   Run the oven and check all functions.

«
...
33
34
35
36
37
...
»

Содержание E30MO65GSSB

































































Отзывы:

Нет отзывов

Похожие инструкции для E30MO65GSSB

Бренд: Nectre Fireplaces Страницы: 8

Бренд: Veripart Страницы: 44

Combi-Duo Elektro Series

Бренд: Rational Страницы: 72

Бренд: Magic Chef Страницы: 35

Бренд: Gaggenau Страницы: 12

Бренд: URSUS TROTTER Страницы: 8

Бренд: Honey Can Do Страницы: 4

Бренд: Gorenje Страницы: 100

Бренд: Brandt Страницы: 17

Бренд: Russell Hobbs Страницы: 32

Бренд: D’amani Страницы: 28

Бренд: Jenn-Air Страницы: 36

Бренд: Orbegozo Страницы: 52

Бренд: SALCO Страницы: 96

Бренд: Toastmaster Страницы: 24

Бренд: Beko Страницы: 40

Бренд: Beko Страницы: 36

Бренд: Beko Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды