Electrolux E30MO65GSSB Скачать руководство пользователя

Страница: 3 / 64

Basic Information

1-1

Safe Servicing Practices

Avoid personal injury and/or property damage by observing important Safe Servicing Practices.
Following are some limited examples of safe practices:

1. DO NOT attempt a product repair if you have any doubts as to your ability to complete the repair in a safe and
satisfactory

manner.

2. Always Use The Correct Replacement Parts as indicated in the parts documentation. Substitutions may defeat

compliance with Safety Standards Set For Home Appliances. Do not exceed maximum recommended wattage on

light bulb replacements. Doing so could blow fuses and/or damage transformers.

3. Before servicing or moving an appliance:

• Remove power cord from the electrical outlet, trip circuit breaker to the OFF position, or remove fuse.

4. Never interfere with the proper operation of any safety device.

5. Use ONLY REPLACEMENT PARTS CATALOGED FOR THIS APPLIANCE. Substitutions may defeat compliance

with Safety Standards Set For Home Appliances.

6. GROUNDING: The standard color coding for safety ground wires is GREEN, or GREEN with YELLOW STRIPES.

Ground leads are not to be used as current carrying conductors. It is EXTREMELY important that the service

technician reestablish all safety grounds prior to completion of service. Failure to do so will create a hazard.

7. Prior to returning the product to service, ensure that:

• All electrical connections are correct and secure.

• All electrical leads are properly dressed and secured away from sharp edges, high-temperature components,

and

moving

parts.

• All non-insulated electrical terminals, connectors, heaters, etc. are adequately spaced away from all metal

parts

and

panels.

• All safety grounds (both internal and external) are correctly and securely connected.

• All panels are properly and securely reassembled.

Содержание E30MO65GSSB

































































Результаты поиска

Содержание E30MO65GSSB

Отзывы:

Похожие инструкции для E30MO65GSSB

Бренды по названию

Популярные бренды

Electrolux E30MO65GSSB, Техническое и сервисное руководство

Результаты поиска

Содержание E30MO65GSSB

Отзывы:

Похожие инструкции для E30MO65GSSB

Бренды по названию

Популярные бренды