Electrolux E30MO65GSSB Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 64

background image

Component Teardown

4-5

HEATING ELEMENT REMOVAL

1. Remove two (2) screws holding heating element to

heater duct.

2. Loosen two (2) screws holding holders to heater duct

and take heating element out of heating element
holders. Heating element is free.

Oven Lamp And Lamp Socket
Removal

1. Disconnect oven from power supply and remove

outer case.

2. Discharge high voltage capacitor.

3. Bend the tab of the air guide holding the lamp socket.

4. Lift up the oven lamp socket.

5. Pull the wire leads from the oven lamp socket by

pushing the terminal hole of the oven lamp socket
with the small flat type screw driver. The oven lamp
socket is free.

To discharge the high voltage capacitor, wait for 60
seconds and then short-circuit the connection of
the high-voltage capacitor (that is the connecting
lead of the high-voltage rectifier) against the
chassis with the use of an insulated screwdriver.

After completely installing the heating element,
bend the top of the heating element holder to
inside using by long nose pliers as shown in the
following illustration.

Figure 4-2. Heating Element Removal

Figure 4-3. Oven Lamp Socket Removal

Fan Motor Removal

Removal

1. Disconnect the oven power supply cord and remove

outer case.

2. Discharge high voltage capacitor.

3. Disconnect the wire leads from the fan motor.

4. Remove one (1) screw holding the fan motor

grounding wire to the air guide (Right).

5. Remove three (3) screws holding the chassis support

to the rear cabinet, waveguide and control panel back

plate.

6. Remove the chassis support from the oven.

7. Remove one (1) screw holding the magnetron air

guide to the waveguide.

8. Remove the magnetron air guide from the waveguide.

9. Disconnect wire leads from the fan motor.

10. Release the main harness from the hole of the fan
duct.

11. Release the thermistor harness from the hole of the

fan duct.

12. Release one (1) tab holding the fan duct to the rear
cabinet.

13. Release one (1) tab holding the fan duct to the air

guide (Right).

14. Remove the fan duct assembly from the oven.

To discharge the high voltage capacitor, wait for 60
seconds and then short-circuit the connection of
the high-voltage capacitor (that is the connecting
lead of the high-voltage rectifier) against the
chassis with the use of an insulated screwdriver.

«
...
47
48
49
50
51
...
»

Содержание E30MO65GSSB

































































Отзывы:

Нет отзывов

Похожие инструкции для E30MO65GSSB

Modernist Microwave In-A-Drawer DMR30M977WS

Бренд: Dacor Страницы: 15

Spacemaker JNM1541DN

Бренд: GE Страницы: 3

Бренд: Taurus Страницы: 144

Бренд: Godrej Appliances Страницы: 204

Бренд: Union Страницы: 37

Бренд: DèLonghi Страницы: 52

B64VS71 0B Series

Бренд: NEFF Страницы: 52

Бренд: GE Страницы: 48

Бренд: cecotec Страницы: 31

Professional Custom VEDO1302T

Бренд: Viking Страницы: 6

Бренд: Häfele Страницы: 28

Бренд: Cafe Страницы: 52

Бренд: Kuppersbusch Страницы: 14

Mini Oven UK 06/05

Бренд: Dualit Страницы: 8

SmartSmoker 250

Бренд: Cookshack Страницы: 18

Voltas Beko MC 28 BD

Бренд: TATA Motors Страницы: 72

Бренд: Teka Страницы: 76

Haier HWO60SM5S9BH

Бренд: CANDY HOOVER Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды