background image

         

17

DRAINING THE WATER

B.1.4.1 Manual draining

The 

AOFP061U, AOFP101U, AOFP102U

 have a drain hole and

plug, and when the plug is removed any liquids in the chamber

flow out into the tray positioned under the cabinet.  This tray must
be emptied once a day.  Replace the drain plug immediately after
cleaning.

Note: make sure the drain tray has been emptied before
removing the drain plug.

           

B.1.4.2 Automatic draining
For AOFP061U, AOFP101U and AOFP102U models

: periodic

emptying of the liquid drain tray can be avoided by connecting
the chamber drain, located on the bottom of the appliance, to a
drainage system, or by connecting a hose to the drain and

running the water into a floor grate.

For AOFP201RU models

: periodic emptying of the liquid drain

tray can be avoided by connecting the cell drain, located on the
evaporator tray, to a drainage system with the special accesso-
ries supplied (see pictures below), choosing the most suitable

side for draining the condensation.

Installation of condensate plumbing

                               

                 

HEATING

CABLE (*)

                   

HEATING
CABLE (*)

                       

                        

          

-5

1

2

4

5

6

3

Содержание AOFP061U












Отзывы: