manualshive.com logo in svg

Elcometer BG80DL, Руководство по эксплуатации

Поделиться
Скачать
Elcometer BG80DL Скачать руководство пользователя страница 5

2

en

2 THE KEYPAD

Activates the primary menu structure containing menu tab groups. These tab groups 
then contain sub menu items, or functions. 

Clears a measurement from a group cell location or set obstruct, and backspace in an 
Alpha Edit Box.

Press to start taking measurements. Scrolls forward through the Hot Menu.

Press to confirm a change or selection. If your gauge is displaying a group log, this key 
advances to a specific bolt number in the group.

In the MENU, MEAS, and EDIT functions this key acts as a back or escape function. If 
your gauge is displaying a group log, this key toggles the display options; RF, RECT or 
DIGITS. Scrolls backward through the Hot Menu functions.

Navigation Keys.

In menus this key activates list and edit boxes, displays and saves measurements to 
bolt group locations.
While making measurements, displays the group log file.

This key has two completely different functions:
•

Reference Lengths

 - When measuring reference lengths, press to locate

automatically the detection point (end of the bolt or target), and optimise the gauge
settings.

•

High Speed Update

 - When using the Elcometer NDT shut-off box, installed and

connected to a pump, press to activate the high speed update mode.

Switches the gauge ON or OFF.
Note: The gauge will automatically switch off when idle for 5 minutes. All current 
settings are automatically saved prior to switching off.

0(18

&/5

0($6

2.

(6&

(17(5

$872

6(7

Содержание BG80DL















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды