manualshive.com logo in svg

Elcometer BG80DL, Руководство по эксплуатации

Поделиться
Скачать
Elcometer BG80DL Скачать руководство пользователя страница 38

35

en

setup file in your gauge was somehow corrupted, and you do not have immediate access to a computer to
re-load the factory setup back into the gauge. This gives you the ability to load and modify a basic setup as
follows:
1.

Press MENU/SETUP/DEFAULT SETUP function.

2.

Press ENTER to activate the confirmation screen.

3.

Press OK to confirm and to return to the measurement screen.

18 DATA TRANSFER SOFTWARE

Software is available which allows data to be transferred from your gauge to a PC. Presently Elcometer
supplies Bolt Link software for this purpose.

To set-up other types of communications software:

1.

Start the communications software.

2.

Configure the software using the following parameters:

Data Bits - 8

, 

Parity - None

, 

Stop Bits - 1

, 

Baud Rate 1200 (to print a report), or 9600 to transfer

data file

.

Note: A report can be printed to a communications program (i.e. HyperTerminal), or printed to a serial
printer using A4 or 8.5" x 11" paper.

3.

Set the communications software COM port to the port number that the gauge is connected to.

18.1 TRANSFERRING MEASUREMENT DATA TO YOUR COMPUTER

18.1.1 RS-232 Connector

The RS-232 connector, located on the bottom end cap of the gauge, is a 2 pin female Lemo connector. It
is designed to connect directly from the gauge to a standard AT serial port on a PC. A Lemo to 9 pin serial
cable is supplied with the gauge.

Note: This connector is also used to upgrade the gauge with the latest version of firmware.

18.1.2 USB to Serial Converter

Some newer laptop computers do not have standard serial ports. In this case, use the USB to Serial
converter supplied with the gauge.

18.1.3 Computer System Requirements

Bolt link requires a PC running Windows 98 or better. 

18.1.4 Installing Bolt Link

Bolt Link comes on a CD-ROM with an automatic installer program. Place the CD in your computer's CD
tray and close the door. Open the CD-ROM by double clicking on the My Computer ICON, then double click
on the CD. Finally, double click on the SETUP icon to begin the installation.
Refer to the help section in Bolt Link software for the complete operating manual, setup, and operation.

18.1.5 Using the XFER menu

The XFER menu of your gauge is used in conjunction with the Bolt Link PC software. The steps below
outline the procedure for accessing the XFER menu and basic operation as follows:
1.

Press MENU and then scroll to the XFER menu.

2.

Use UP and DOWN to scroll through the sub menu items until the desired option is highlighted.

3.

Press the ENTER key to activate the option selected.

4.

Once the Backup or Restore function has been completed, press MEAS once to return to the menu
items, or twice to return to the measurement mode.

Содержание BG80DL















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды