manualshive.com logo in svg

Elcometer BG80DL, Руководство по эксплуатации

Поделиться
Скачать
Elcometer BG80DL Скачать руководство пользователя страница 2

en

This product meets the Electromagnetic Compatibility Directive.

The product is Class A, Group 1 ISM equipment according to CISPR 11

Group 1 ISM product: A product in which there is intentionally generated and/or used conductively coupled
radio-frequency energy which is necessary for the internal functioning of the equipment itself.

Class A product are suitable for use in all establishments other than domestic and those directly connected
to a low voltage power supply network which supplies buildings used for domestic purposes.

Note: In the close presence of some radio transmitters, erroneous readings may be given. If this occurs tests
should be repeated at another location.

All other trademarks acknowledged.

Material Safety Data Sheets for the ultrasonic couplant supplied with the BG80DL & BG80TDL and
available as an accessory, are available to download via our website:

Elcometer NDT Ultrasonic Couplant Material Safety Data Sheet :

www.elcometerndt.com/images/MSDS/elcometer_ultrasonic_couplant.pdf

© Elcometer Limited 2011-2013. All rights reserved. No part of this document may be reproduced,
transmitted, transcribed, stored (in a retrieval system or otherwise) or translated into any language, in any
form or by any means (electronic, mechanical, magnetic, optical, manual or otherwise) without the prior
written permission of Elcometer Limited. 

TMA-0562 Issue 02

Text with cover: 23866

Содержание BG80DL















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды