6
web panels (576 x 792 mm) for the right-hand
(divided) door wing. Measure the panels before
installing them.
Page 31
30/a:
Slide the DT latch (Pos. 3) into the guide rail of
the door closing profile with the hole (item 11). In
addition, attach a hexagonal bolt approximately 5 cm
from the edge at both ends of this guide rail (refer to
the profile diagram).
30/b:
One bolt needs to be pre-assembled at each
end of two door closing profiles (approx. 5 cm from
the edge) (item 9).
30/c:
On the third door closing profile (item 9), two
bolts need to be pre-assembled in the middle and two
bolts at each end, approximately 5 cm from the edge.
Page 32
30/e:
Hinge blades have to be attached to two short
side door profiles (item 10) (refer to the detail
drawing). Attach a hinge blade to each end of the
side door profile, approximately 10 cm from the edge.
Make sure that the hinge blades are inserted in the
way shown in the profile diagram.
Page 33
Note:
No pre-assembly is required for the fourth side door
profile.
Page 34
Assembly of the upper door wing
30/h:
Attach the side door profile with the striker
plate on the right-hand side of the door closing profile
with the hole (item 11). On the left-hand side, attach
the side door profile with the two pre-assembled
hinge blades (refer to step 30/e).
During assembly of the side door profiles, make sure
that the hinges and the striker plate are correctly
positioned (refer to the profile diagram).
Page 36
30/k:
Insert the handle (item 5) from the outside
through the hole on the lower door closing profile.
On the inside, push on the locking device (item 6)
and secure it with a washer (item 1) and a self-drilling
screw with tapping screw thread (item 16). Make sure
that after the locking devices are installed they
are positioned at a 90 degree angle (clockwise) in
relation to the handle (see illustration below), as this
is necessary to ensure that the door subsequently
opens and closes smoothly.
Page 37
Assembly of the lower door wing
30/l:
Attach the side door profile without bolts on the
right-hand side of the door closing profile (item 9).
On the left-hand side, attach the side door profile
with the two pre-assembled hinge blades (refer to
step 30/e). During assembly of the side door profiles,
make sure that the hinges are correctly positioned
(refer to the profile diagram).
Page 39
Figure 30/o (external view):
Note the notch on the
lock housing.
30/o:
The door latch is attached to the lower door
wing on the side without the hinge.
First insert the latch (item 7) knob-first into the lock
housing (item 8). Align the door latch on the upper
door profile so that the notch on the housing rests
against the side profile of the door.
Then slide the knob on the latch up to the second
marking so that the holes on the latch and the
housing line up. Attach the door latch to the door
profiles using two self-drilling screws with tapping
screw threads.
Page 40
Left-hand door wing
Important note:
The outside of the plastic web panels (with UV
coating) is marked „
Außenseite / Outside
“ at the
edge, and it is also the side onto which the protective
film has been stuck.
Only remove the protective film from the plastic web
panel you are currently installing.
Important note – take care not to mix up the
components:
There is only a minimal difference in terms of size
between the plastic web panels 85.043.19 and
85.043.04. Make sure that you fit the longer plastic
web panels (576 x 798 mm) for the left-hand door
wing. Measure the panels before installing them.
Page 41
30/p:
Slide a DT latch (item 2) into each of the guide
rails of the door closing profiles (item 5). In addition,
fasten a hex screw to each end approx. 5 cm from
the edge.
Page 42
30/s:
Fasten three hinge blades to one of the side
door profiles (item 6). Make sure that the hinge
blades are inserted in the way shown in the profile
diagram.
ABA_SM_TeilGB.pmd
07.04.2006, 10:39
6
