GB
- 25 -
opens fully when the throttle handle is pressed
right through. This is the case if the carburetor
slide (Fig. 13a) is completely opened when the
throttle is fully activated. Figure 13a shows the
correct setting. If the carburetor slide is not com-
pletely open, it must be adjusted.
The following steps are required to adjust the
throttle cable:
•
Undo the adjusting screw (Fig. 13b/Item D)
until the carburetor slide is completely open
when the throttle is fully activated, as shown
in Figure 13a.
9.6 Setting the idling speed
Important!
Set the idling speed when the equip-
ment is warm.
Only an authorized service center is allowed to
set the idling speed. The start-up speed of the
cutting tool must be at least 1.25 times the idling
speed.
9.7 Applying grease to the gear unit
After every 20 hours of use add a little gear grea-
se (approx. 10 g) at the lubrication point (C) (Fig.
7c).
10. Cleaning, storage, transport and
ordering of spare parts
10.1 Cleaning
•
Keep the handles free of oil so that you can
maintain a firm grip.
•
Clean the equipment as required with a damp
cloth and, if necessary, mild washing up
liquid.
Notice:
Always pull out the spark boot plug each time
before carrying out any cleaning. Never immerse
the equipment in water or other liquids in order to
clean it.
Store the equipment in a safe and dry place out of
the reach of children.
10.2 Storage
Important: Never put the equipment into storage
for longer than 30 days without carrying out the
following steps.
Storing the equipment
If you intend to store the equipment for longer
than 30 days, the equipment must be prepared
accordingly. Otherwise the fuel still remaining in
the carburetor will evaporate and leave a rubbery
sediment. This can cause problems when starting
up the equipment and may require expensive
repairs.
1. Slowly remove the fuel tank cap to release
any pressure that may have formed in the
tank. Carefully empty the tank.
2. To remove the fuel from the carburetor, start
the engine and let it run until it stops.
3. Leave the engine to cool (approx. 5 minutes).
Note:
Store the equipment in a dry place and
far away from possible ignition sources such as
an oven, a gas-
fi
red hot water boiler, a gas-
fi
red
dryer, etc.
Putting the equipment back into operation
1. Remove the spark plug (see section 9.4).
2. Clean the spark plug and check that the
electrode gap is correct, or insert a new spark
plug with the correct electrode gap.
3. Prepare the equipment for operation.
4. Fill the tank with the relevant mixture of fuel
and oil. See the section „Fuel and oil“.
10.3 Transport
To transport the machine, empty the petrol tank
as described in section 10. Clean coarse dirt o
ff
the equipment with a brush or hand brush. Dis-
mantle the drive rod mechanism as described in
section 5.1.2.
10.4 Ordering spare parts
Please provide the following information on all
orders for spare parts:
•
Model/type of the equipment
•
Article number of the equipment
•
ID number of the equipment
•
Part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
11. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Defective components must be dispo-
sed of as special waste. Ask your dealer or your
local council.
Anl_GC_BC_30_1_AS_EX_I_SPK9.indb 25
Anl_GC_BC_30_1_AS_EX_I_SPK9.indb 25
19.07.2017 09:09:23
19.07.2017 09:09:23
