Eiki LC-WB200 Скачать руководство пользователя

Страница: 6 / 80

Safety Instructions

Openings in the cabinet are provided for

ventilation. To ensure reliable operation of the

product and to protect it from overheating, these

openings must not be blocked or covered.

CAUTION

Hot air is exhausted from the exhaust vent. When

using or installing the projector, the following

precautions should be taken.

– Do not put any flammable object or spray can

near the projector, hot air is exhausted from the

ventilation holes.

– Keep the exhaust vent at least 3’ (1 m) away

from any objects.

– Do not touch a peripheral part of the exhaust

vent, especially screws and metallic parts.

These areas will become hot while the

projector is being used.

– Do not put anything on the cabinet. Objects put

on the cabinet will not only get damaged but

also may cause fire hazard by heat.

– Make sure that there is no object under the

projector to prevent from covering the bottom

openings.

Cooling fans are provided to cool down the

projector. The fans’ running speed is changed

according to the temperature inside the projector.

Moving the Projector

When moving the projector, replace the lens cap

and retract adjustable feet to prevent damage to

the lens and cabinet.

When the projector is not in use for an extended

period, put it into the supplied carrying case with

the lens side up.

Air Circulation

Do not pitch the projector more

than 40 degrees from above and

below.

Do not point the projector up to

project an image.

Do not point the projector down to

project an image.

Do not put the projector on either

side to project an image.

Install the projector properly. Improper installation

may reduce the lamp life and cause a fire hazard.

Do not roll the projector more

than 20 degrees from side to

side.

20°

CAUTION IN CARRYING OR

TRANSPORTING THE PROjECTOR

– Do not drop or bump the projector, otherwise

damages or malfunctions may result.

– When carrying the projector, use a suitable

carrying case.

– Do not transport the projector by courier or

any other transport service in an unsuitable

transport case. This may cause damage to the

projector. For information about transporting

the projector by courier or any other transport

service, consult your dealer.

– Do not put the projector in a case before the

projector is cooled enough

Installing the Projector in Proper

Position

Exhaust Vent

(Hot air exhaust)

Air intake Vent

CAUTION

The carrying case (supplied) is intended for

protection against dust and scratches on surface

of the cabinet, and it is not designed to protect

an appliance from external forces. Do not

transport the projector by courier or any other

transport service with this case, otherwise the

projector can be damaged. When handling the

projector, do not drop, bump, subject it to strong

forces, or put other things on the cabinet.

40°

Air intake Vent

Compliance

Air Intake Vent

Exhaust Vent

(Hot air exhaust)

Содержание LC-WB200

















































































Результаты поиска

Содержание LC-WB200

Отзывы:

Похожие инструкции для LC-WB200

Бренды по названию

Популярные бренды

Eiki LC-WB200, Руководство пользователя

Результаты поиска

Содержание LC-WB200

Отзывы:

Похожие инструкции для LC-WB200

Бренды по названию

Популярные бренды