Efka AB600A5010 Скачать руководство пользователя | Manualshive

Страница: 15 / 64

background image

- AB AB600A5010

Instruction Manual

- 15 -

6.3 Transmission Ratio

N

OTE

The transmission ratio must always be input if no transmission ratio of 1:1 exists, because only motors with
integrated incremental transmitters will be used.

The transmission ratio should be determined and set as

precisely as possible!

The transmission ratio between motor shaft and shaft of the sewing machine head must be input, so that the set
speeds of parameters

110...117

correspond to the sewing speeds.

Function

Parameters

Transmission ratio between motor shaft and machine shaft

(trr)

272

The transmission ratio can be selected within a range of 150...40000 using parameter

272

.

Example:

With a motor pulley diameter of 40 mm and a sewing machine head pulley diameter of
80

mm

the

value

500

can

be

calculated

using

the

formula

below.

If the value 2000 has been selected in parameter 272, it follows that the motor pulley is
double the size of the sewing machine head pulley.

Motor pulley diameter

Value of parameter

272

= -------------------------------------------------------------------- x 1000

Machine pulley diameter

6.4 Selection of Functional Sequences (Thread Trimming Operations)

This drive is suitable for different lockstitch, chainstitch and overlock machines. The mode for the functional
sequence required on the respective machine can be selected using parameter

290

.

A

TTENTION

Before  switching  the  functional  sequences,  you  must  disconnect  input  and  output  plug -and-
socket  connections  between  control  and  machine.  Please  ensure  that  the  functional  sequence
(mode)  suitable  for  the respective  machine  is selected.

Settings with parameter 290 are possible only after the power is turned On.

You will find a summary of the modes that can be set and the corresponding machines and adapter cords, to
include available output signals in the List of Parameters chapter: Table of adapter cords.

Further information see chapter "Timing Diagrams" for the various modes.

The possible functions are listed in the section "Parameter list".

6.5 Key functions of the input in1

The  function  which  is triggered  by pressing  a button or  switch connected  to  input  in1 can be  selected with
parameter  240.
The  possible functions  are  listed in the  section "Parameter  list"

6.6 Positioning speed

Function

with

or

without

control panel

Parameters

Positioning speed

(n1)

110

The positioning speed can be set using parameter

110

on the control within a range of 70...390 RPM.

«
...
13
14
15
16
17
...
»

Содержание AB600A5010

































































Отзывы:

Нет отзывов

Похожие инструкции для AB600A5010

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 20

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: Lawler Страницы: 4

Бренд: Hama Страницы: 46

Бренд: Galcon Страницы: 35

Бренд: Lamtec Страницы: 136

Gemini GEM-P9600

Бренд: NAPCO Страницы: 6

Gemini GEM-P816

Бренд: NAPCO Страницы: 56

Бренд: OMC Страницы: 18

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

FrameSaver 9120

Бренд: Paradyne Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды