EEZ RV EezTire E518 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 35

EEZ RV EezTire E518 Скачать руководство пользователя страница 28

28

electronics in the engine compartment and dashboard they can get
interference. As well as the structure of the frame, number of slides
and the amount metal on many of the new rigs of all styles can also
be a factor. So, you can get interference for issues other than
distance. Systems will typically read fine sitting still

, you won’t see the

interference until about 20-30 minutes or longer into the trip. It is
impossible to predict whether you need a booster.

17. Is signal booster available? Answer: Yes, we do carry an optional
signal booster for vehicles or if it determined you have either
electronic or structural interference. You may order an optional
Repeater/Booster on our site at

www.eezrvproducts.com

18. Can I reset the perimeters to factory default?

Answer: Yes, to restore perimeters to factory defaults, turn off the
monitor, press the set button and turn the monitor on at the same
time. The red light will flash, and factory perimeters settings
restored. This will not reset the sensors.

19. Do I need a signal booster (transceiver)?

Answer: It used to be easy to determine if you would need one. The
general rule was around 53 ft, but nowadays, though the big diesel
pushers have so much electronics in the engine compartment and
dashboard, they can get interference. As well as the structure of the
frame, the number of slides and the amount of metal on many of the
new rigs of all styles can also be a factor. So, you can get interference
for reasons other than distance. Systems will typically read fine sitting
still

; you won’t see the interference until about 20

-30 minutes into

the trip.

20. Does this system measure temperature as well as pressure?

«
...
26
27
28
29
30
...
»

Содержание EezTire E518




































Отзывы:

Нет отзывов