Edwards EXC120 Скачать руководство пользователя страница 40

Страница: 40 / 54

D396-14-880 Issue J

Page 32

Edwards and the Edwards logo are trademarks of Edwards Limited.

Installation

3.13.3

Vent options

Note:

The Axial Emergency condition is only available on the EXC300M Controller. On other Controllers, the
position of DIP switch 2 can be ignored.

DIP switches 2 to 4 are used to select the vent-valve control options (refer to

Section 1.8

). Select the required vent

options as shown in

Table 10

Note however, that if the electrical supply to the Controller fails, the Controller will always switch off the electrical
supply to the vent-valve when the EXT pump speed falls to below 50% of full speed (see

Section 1.8.1

Table 10 - Selection of vent-valve control options

DIP switch positions

Vent option(s) selected

(Vent on

Axial

Emergency)

(Vent on

Stop)

(Vent on

Stop)

Off

No optional vent selected: Vent when EXT pump speed
falls to below 50% of full speed after Stop is selected.

Off

Vent on Stop.

Off

Vent on Fail and Vent when EXT pump speed falls to
below 50% of full speed after Stop is selected.

Off

Vent on Fail and Vent on Stop.

Factory setting.

Off

Vent on Axial Emergency

†

and Vent when EXT pump

speed falls to below 50% of full speed after Stop is
selected.

†

Only available on the EXC300M Controller.

Off

Vent on Axial Emergency

†

and Vent on Stop.

Off

Vent on Axial Emergency

†

and Vent on Fail and

Vent when EXT pump speed falls to below 50% of full
speed after Stop is selected.

Vent on Axial Emergency

†

and Vent on Fail and

Vent on Stop.

Содержание EXC120


















































Результаты поиска

Содержание EXC120

Отзывы:

Бренды по названию

Популярные бренды

Edwards EXC120, Инструкция по эксплуатации

Результаты поиска

Содержание EXC120

Отзывы:

Бренды по названию

Популярные бренды