manualshive.com logo in svg

Edwards EXC120, Инструкция по эксплуатации

Поделиться
Скачать
Edwards EXC120 Скачать руководство пользователя страница 11

© Edwards Limited 2008. All rights reserved. 

Page 3

Edwards and the Edwards logo are trademarks of Edwards Limited.

Introduction

D396-14-880 Issue J

1.3

Controls and indicators (EXC120/300/300M only)

Note:

In addition to the controls and indicators on the front panel, the EXC120, EXC300 and EXC300M Controllers 
have an electrical supply isolator on the rear panel (see Figures 

3

 to 

5

).

The controls and indicators on the front panel of the EXC120, EXC300 and EXC300M Controllers are shown in Figures 

1

 and 

2

 and are described below.

Start/Stop

Use this latching button to alternately Start or Stop the EXT pump. A LED on the button goes on when EXT Start has 
been selected. Note that:

z

The button is wired in series with the Start/Stop input on the logic interface (see 

Section 1.7.3

). The EXT 

pump will not start until Start is selected from this front panel button and the Start/Stop input is closed. The 
Controller is supplied with a wire link to close the Start/Stop input. 

z

If the LED on the button is on, it only means that Start has been selected; it does not necessarily mean that 
the pump has successfully started.

z

The Controller delays the Start operation until the Interlocks are closed (refer to 

Section 1.7.3

); therefore, 

the EXT pump will not necessarily start to operate when you select Start. If you select Start and the 
Interlocks are not closed, the LED on the button will flash.

This button is also used to reset the Controller after Fail or Axial Emergency condition (see 

Section 4.9

).

Standby

Use this latching button to select pump Standby mode at any time. In Standby, the rotational speed of the EXT pump 
is reduced to 70% of its full rotational speed. Selection of Standby prolongs the life of the pump bearings. Note that:

z

The button is wired in parallel with the Standby input on the logic interface (see 

Section 1.7.3

) and you can 

use either the button or the input to select Standby.

z

The LED on the button is on when Standby is selected (either by the button or by the Standby input).

Heater

Use this switch to switch on the electrical supply to the bakeout band. Note that the Controller only switches on the 
electrical supply to the bakeout band when the EXT pump speed reaches the Normal speed setpoint (see 

Section 1.7.4

).

The LED on the switch is on when the electrical supply to the bakeout band is switched on; this LED can therefore be 
used as an indication that the pump has reached Normal speed.

Содержание EXC120























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды