manualshive.com logo in svg

ECS 761GXM-M2, Руководство пользователя, Страница: 16 / 58

Поделиться
Скачать
ECS 761GXM-M2 Скачать руководство пользователя страница 16

10

Installing the Motherboard

Connecting Case Components

After you have installed the motherboard into a case, you can begin connecting the
motherboard components. Refer to the following:

1

Connect the CPU cooling fan cable to 

CPU_FAN1

.

2

Connect the system cooling fan connector to 

SYS_FAN1

.

3

Connect the case switches and indicator LEDs to the 

PANEL1

.

4

Connect the standard power supply connector to 

PWR1

.

5

Connect the auxiliary case power supply connector to 

PWR2

.

6

Connect the case speaker cable to 

SPK1

.

Connecting 20/24-pin power cable

Users please note that the 20-pin and 24-pin power cables can both be
connected to the PWR1 connector. With the 20-pin power cable, just align
the 20-pin power cable with the pin 1 of the PWR1 connector. However,
using 20-pin power cable may cause the system to become unbootable or
unstable because of insufficient electricity. A minimum power of 300W is
recommended for a fully-configured system.

With ATX v2.x power supply, users please note
that when installing 24-pin power cable, the
latches of power cable cling to the right side of
PWR1 connector latch.

With ATX v1.x power supply, users please note
that when installing 20-pin power cable, the
latch of power cable  falls on the left side of the
PWR1 connector latch, just as the picture
shows.

20-pin power cable

24-pin power cable

Содержание 761GXM-M2



























































Отзывы:

Нет отзывов