ECR Utica Heating UH15B-060K Скачать руководство пользователя страница 6

Страница: 6 / 44

WARNING

Keep boiler area clear and free from combustible

materials, gasoline and other flammable vapors and

liquids.

DO NOT obstruct air openings to the boiler room.

Modification, substitution or elimination of factory

equipped, supplied or specified components may

result in personal injury or loss of life.

Installation and service of this boiler shall be performed

by a qualified installer.

When this product is installed in the Commonwealth

of Massachusetts the installation shall be performed

by a Licensed Plumber or Licensed Gas Fitter.

WARNING

Combustion chamber insulation in this product

contains ceramic fiber material. Ceramic fibers

can be converted to cristobalite in very high

temperature applications. The International Agency

for Research on Cancer (IARC) has concluded,

Crystalline silica inhaled in the form of quartz

or cristobalite from occupational sources is

carcinogenic to humans (Group1). Avoid breathing

dust and contact with skin and eyes. Use NIOSH

certified dust respirator (N95). This type of

respirator is based on the OSHA requirements

for cristobalite at the time this document was

written. Other types of respirators may be needed

depending on the job site conditions. Current

NIOSH recommendations can be found on the

NIOSH website

https://www.cdc.gov/niosh/topics/

silica/.

NIOSH approved respirators, manufacturers,

and phone numbers are also listed on this website.

Wear long-sleeved, loose fitting clothing, gloves,

and eye protection. Apply enough water to the

combustion chamber lining to prevent dust. Wash

potentially contaminated clothes separately from

other clothing. Rinse clothes washer thoroughly.

NIOSH stated First Aid. Eye: Irrigate immediately.

Breathing: Fresh air.

2 - SAFETY SYMBOLS AND WARNINGS

2.2 For Your Safety

Manufacturer recommends a carbon monoxide detector

located on each floor of your home. Follow your detector's

instructions for operation and verification. Some

jurisdictions may, by law, require.

WARNING

Fire, Explosion, Asphyxiation, Electrical shock

hazard! Flooding will result in damages such as

electrical problems, corrosion, inoperative parts,

mold and other unforeseen issues which can

occur over time. Any equipment determined by

a professional as damaged by a flood, defined as

excess of water or other liquid, shall be replaced.

Failure to follow these directions will result in a

Hazardous Situation.

PN 240012809, Rev. C [11/15/2020]

Содержание Utica Heating UH15B-060K













































Результаты поиска

Содержание Utica Heating UH15B-060K

Отзывы:

Похожие инструкции для Utica Heating UH15B-060K

Бренды по названию

Популярные бренды

ECR Utica Heating UH15B-060K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Heating UH15B-060K

Отзывы:

Похожие инструкции для Utica Heating UH15B-060K

Бренды по названию

Популярные бренды