ECR Utica Heating UH15B-060K Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 44

background image

12

4 - CONNECTING SUPPLY & RETURN PIPING

Circulators in following illustrations are mounted on system supply side, mounting on system return side is also

acceptable practice.

Figure 4-2 - Circulators Mounted on Supply

System, Boiler Used In Configuration with Chiller

System. See Special Conditions, Page 9

PIPING LEGEND:

4.6 Special Conditions

• System piping exposed to freezing conditions: Use

inhibited propylene glycol solutions certified by fluid

manufacturer for use with closed water heating

system. Do not use automotive or ethylene glycol.

Do not expose boiler and piping to freezing
temperatures.

Note

• Boiler installed above radiation level (or as required

by authority having jurisdiction). Integral low water

switch is provided in boiler.

• Boiler used in connection with refrigeration system.

Install piping in parallel with boiler, with appropriate

valves to prevent chilled medium from entering boiler.

• System piping connected to heating coils located in air

handling unit exposed to refrigerated air circulation.

Install flow control valves or other automatic means

to prevent gravity circulation of boiler water during

cooling cycle.

PN 240012809, Rev. C [11/15/2020]

«
...
10
11
12
13
14
...
»

Содержание Utica Heating UH15B-060K













































Отзывы:

Нет отзывов

Похожие инструкции для Utica Heating UH15B-060K

Бренд: Toastmaster Страницы: 13

Бренд: IBC Technologies Страницы: 80

Vitotronic 100 GC1

Бренд: Viessmann Страницы: 132

Бренд: Arikazan Страницы: 38

Burnit PelleBurn 15

Бренд: Sunsystem Страницы: 68

OPTIMAX HE 25 S

Бренд: Ferroli Страницы: 40

Бренд: Ferroli Страницы: 44

Бренд: Ferroli Страницы: 52

ECONCEPT TECH 25 A

Бренд: Ferroli Страницы: 32

DOMIcompact C 24

Бренд: Ferroli Страницы: 28

DOMIcompact F 30 D

Бренд: Ferroli Страницы: 40

Бренд: Ferroli Страницы: 40

Бренд: Ferroli Страницы: 68

Бренд: Ferroli Страницы: 48

divaproject C24

Бренд: Ferroli Страницы: 93

Bluehelix PRO C

Бренд: Ferroli Страницы: 96

BLUEHELIX TECH RRT H

Бренд: Ferroli Страницы: 252

Multidea Evo 100

Бренд: Bongioanni Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды