ECR Utica Heating UH15B-060K Скачать руководство пользователя страница 21

Страница: 21 / 44

8 - VENT DAMPER INSTALLATION & INSTRUCTIONS

8.1 Vent Damper

Connecting The Vent Damper And Vent Connector

Refer to page 4 for size and location of vent (flue opening).

NOTICE

Damper blade on furnished vent damper has 1/2

square inch hole (approximately 3/4” diameter).

Boilers equipped with intermittent ignition, hole

should be plugged by using plug supplied with vent

damper.

Follow damper installation instructions provided with

damper.

Position furnished vent damper on top of flue outlet

collar. Fasten damper securely to flue outlet collar with

sheet metal screws. Verify damper blade has clearance

to operate inside of diverter. Do not modify either draft

diverter or vent damper during installation.

As An Option

Damper may be installed in horizontal or vertical

position, closer to flue outlet collar preferred. See

Figures 8-1, 8-2, 8-3 and enclosed vent damper

instructions.

Install vent damper to service only single boiler for

which it is intended. Damper position indicator shall be

in visible location following installation. Locate damper

so it is accessible for servicing. See Figure 8-2.

Damper must be in the open position when appliance

main burners are operating.

Boiler is equipped with factory wired harness that plugs

into vent damper.

Slope pipe up from boiler to chimney not less than 1/4”

per foot.

Run pipe as directly as possible with as few elbows as

possible.

Do not connect to fireplace flue.

End of vent pipe must be flush with inside face of

chimney flue. Use a sealed-in thimble for chimney

connection.

10.

Clearance of not less than 6 inches (152mm) between

Vent Damper and combustible material must be

maintained. Additional clearance should be allowed for

service of Vent Damper.

11.

Vent Damper position indicator must be in visible

location following installation.

Fasten sections of vent pipe with sheet metal screws to

make piping rigid. Support horizontal potions of vent

system to prevent sagging. Use stovepipe wires every 5’ to

support pipe from above. Use double wall vent pipe if vent

pipe must go through crawl space. Where vent pipe passes

through combustible wall or partition, use ventilated metal

thimble. Thimble should be 4 inches larger in diameter than

vent pipe.

Figure 8-1 - Vent Damper Installation

PN 240012809, Rev. C [11/15/2020]

Содержание Utica Heating UH15B-060K













































Результаты поиска

Содержание Utica Heating UH15B-060K

Отзывы:

Похожие инструкции для Utica Heating UH15B-060K

Бренды по названию

Популярные бренды

ECR Utica Heating UH15B-060K, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Heating UH15B-060K

Отзывы:

Похожие инструкции для Utica Heating UH15B-060K

Бренды по названию

Популярные бренды