ECR UTICA BOILERS UB95M-200 Скачать руководство пользователя

Страница: 3 / 48

iii - rules for safe installation and operation

ii - safety symbols and warninGs

WARNING

This appliance has been equipped for residential instal-

lations. If used for commercial applications, any and all

additional code requirements must be adhered to for in-

stallation. This may require additional controls, including

but not limited to an external water cut off, a manual reset

high temperature limit, and wiring and/or piping modifi-

cations. The manufacturer is not responsible for any field

installation changes made to a boiler installation which are

not described or acknowledged in this manual.

NOTICE

IMPORTANT: Failure to follow these instructions could

cause a malfunction of the boiler and result in death, seri-

ous bodily injury, and/or property damage. For assistance

or additional information, consult a qualified installer,

service agency, or the gas supplier.

Check all applicable state and local building codes and utility

company requirements before installation. This installation

must conform with these requirements in their entirety. In the

absence of these codes, use NFPA installation codes and good

industry practice.
Before servicing the boiler, allow it to cool. Always shut off any

electricity and gas supply connected to the boiler prior to servic-

ing.
Inspect gas line for leaks.

Be certain gas input rate is correct. Over firing may result in

early failure of the boiler components. This may cause danger-

ous operation. Under firing may result in too much air for the

pre-mix burner causing poor or loss of combustion.
Never vent the products of combustion from this boiler to an

enclosed space. Always vent to the outdoors. Never vent to

another room or to inside a building.

Be sure there is adequate outdoor air supply to boiler for com-

plete combustion.
Follow a regular service and maintenance schedule for efficient

and safe operation.
Keep boiler area clean of debris and free of combustible and

flammable materials.
Proper through-the-wall or through-the-roof combustion

venting shall be in accordance with the materials and methods

described in this manual. Installation must comply with local

codes.
This boiler and related hot water heating systems are not do-it-

10.

yourself items. They must be installed and serviced by qualified

professionals. Ratings above are for sea level applications. The

boiler automatically derates input at a rate of 2% for every 1000

feet above an elevation of 2000 feet (see Table 2). The boiler will

also derate relative to the calorific value of the gas being used.

Use the formula specified in “Measure The Natural Gas Input

Rate” in the Control Manual and Troubleshooting Guide (P/N#

240006104) to determine the proper rate due to derated gas. To

ensure proper operation at 5,000 feet of altitude and above, the

minimum RPM setting; parameter 17, must be raised to 3,200.

Instructions on how to change the parameters are included in

the Parameter Guide, part number 240006105.

NOTICE

Indicates information which should be followed to ensure

proper installation and operation.

The following defined symbols are used throughout this manual to notify the reader of potential hazards of varying risk levels.

DANGER

Indicates an imminently hazardous situation which, if not

avoided, will result in death, serious injury or substantial

property damage.

WARNING

Indicates an imminently hazardous situation which, if not

avoided, may result in death, serious injury or substantial

property damage.

CAUTION

Indicates an imminently hazardous situation which, if not

avoided, may result in injury or property damage.

Содержание UTICA BOILERS UB95M-200

















































Результаты поиска

Содержание UTICA BOILERS UB95M-200

Отзывы:

Похожие инструкции для UTICA BOILERS UB95M-200

Бренды по названию

Популярные бренды

ECR UTICA BOILERS UB95M-200, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UTICA BOILERS UB95M-200

Отзывы:

Похожие инструкции для UTICA BOILERS UB95M-200

Бренды по названию

Популярные бренды