ECR UTICA BOILERS UB95M-200 Скачать руководство пользователя

Страница: 8 / 48

v - before installinG the boiler

OVERHANG

12" MINIMUM

90°

VENT

12" SEPARATION

BETWEEN BOTTOM OF

COMBUSTION AIR INTAKE

AND BOTTOM OF VENT

MAINTAIN 12" MINIMUM

CLEARANCE ABOVE HIGHEST

ANTICIPATED SNOW LEVEL OR

GRADE

MAXIMUM

SEPARATION

18"

MAXIMUM

15"

MAXIMUM

LESS THAN 12" CLEARANCE

12"

MINIMUM

12"

MINIMUM

12" OR MORE CLEARANCE

90°

BRACKET

VENT

18"

MAXIMUM

MAINTAIN 12" MINIMUM

CLEARANCE ABOVE HIGHEST

ANTICIPATED SNOW LEVEL OR

GRADE

12" SEPARATION

BETWEEN BOTTOM OF

COMBUSTION AIR INTAKE

AND BOTTOM OF VENT

12" MINIMUM

OVERHANG

MAXIMUM

SEPARATION

12"

MINIMUM

12"

MINIMUM

When utilizing two or more boilers, each termination must have at least 12 inches of clearance from any adjacent termination. See diagrams

below.

CAUTION

Keep boiler area clean of debris and free of flammable and

combustible materials, vapors, and liquids.

WARNING

Failure to follow these warnings could result in fire, prop-

erty damage, personal injury, or death.

When vent pipe is exposed to temperatures below freez-

ing, such as when it passes through an unheated space or

when a chimney is used as a chaseway, vent pipe must be

insulated with ½”Armaflex or equivalent. In extremely cold

climate areas, use ¾”Armaflex or equivalent.
Combustion air must be clean outdoor air. Combustion air

must not be taken from inside the structure because that

air is frequently contaminated by halogens, which include

fluorides, chlorides, phosphates, bromides and iodides.

These elements are found in aerosols, detergents, bleaches,

cleaning solvents, salts, air fresheners, paints, adhesives,

and other household products.

NOTICE

Condensate trap is integral to the boiler.

Wood frame or concrete blocks may be used to raise the

boiler to maintain drain pitch or to be above external con-

densate pump reservoir.

There is a 115 volt AC receptacle provided on the control

panel to provide power for an external condensate pump

(if needed).

WARNING

Failure to follow these warnings could result in fire, prop-

erty damage, personal injury, or death.
Locate combustion air inlet as far away as possible from

swimming pool and swimming pool pump house. All

combustion air and vent pipes must be airtight and water-

tight. Combustion air and vent piping must also terminate

exactly as shown in Figures 1 and 2. If a concentric vent

termination is being used, refer to Figures 3 through 5 for

proper setup.
Vent connections serving appliances vented by natural

draft shall not be connected into any portion of mechani-

cal draft systems operating under positive pressure.
Solvent cements are combustible. Keep away from heat,

sparks, or open flame. Use only in well ventilated areas.

Avoid breathing in vapor or allowing contact with skin or

eyes.

Содержание UTICA BOILERS UB95M-200

















































Результаты поиска

Содержание UTICA BOILERS UB95M-200

Отзывы:

Похожие инструкции для UTICA BOILERS UB95M-200

Бренды по названию

Популярные бренды

ECR UTICA BOILERS UB95M-200, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UTICA BOILERS UB95M-200

Отзывы:

Похожие инструкции для UTICA BOILERS UB95M-200

Бренды по названию

Популярные бренды