ECR UTICA BOILERS UB95M-200 Скачать руководство пользователя

Страница: 22 / 48

filling boiler with water and purging air

For each of the following systems, refer to the appropriate piping

diagrams in the Installation Manual

Systems With Diaphragm Type Expansion Tanks

Close all zone service valves on the supply and return pip-

ing. Open the feed valve and fill boiler with water. Make

sure air vent is open. Hold relief valve open until water

runs air free for five seconds to rapidly bleed air from

boiler, then let the relief valve snap shut.
Open the zone service valve on the supply pipe for the first

zone. Open the purge valve on the first zone. Feed water

will fill the zone, pushing air out the purge valve. Close the

purge valve when the water runs air free. Close the zone

service valve.
Repeat step 2 for all remaining zones.

Open all service valves. Any air remaining trapped in the

return lines between the service valves and the boiler will

be pushed towards the air vent when the boiler is placed in

operation.
Inspect piping system and repair any leaks immediately.

Systems With Conventional Closed Type Expansion

Tanks

Close all zone service valves on the supply and return

piping and close the expansion tank service valve. Drain

expansion tank. Open the feed valve and fill boiler with

water. Hold relief valve open until water runs air free for

five seconds to rapidly bleed air from boiler, then let the

relief valve snap shut.
Open the zone service valve on the supply pipe for the first

zone. Open the purge valve on the first zone. Feed water

will fill the zone, pushing air out the purge valve. Close the

purge valve when the water runs air free. Close the zone

service valve.
Repeat step 2 for all remaining zones.

Open the expansion tank service valve and the tank vent.

Fill the tank to the proper level and close the tank vent.

Remove the handle from the expansion tank service valve

so the homeowner doesn’t accidentally close it.
Open all service valves. Any air remaining trapped in the

return lines between the service valves and the boiler will

be pushed towards the expansion tank when the boiler is

placed in operation.
Inspect piping system. Repair any leaks immediately.

Xiii - puttinG the boiler in operation

NOTICE

NOTE: Do not use stop leak compounds. Leaks in

threaded connections in the aluminum boiler sections

must be repaired immediately. Aluminum threads will not

seal themselves.

liGhtinG instructions

FOR YOUR SaFEtY REaD BEFORE OPERatiNG!!

WARNING

If you do not follow these instructions exactly, a fire or

explosion may result causing property damage, personal

injury or loss of life.

This appliance does not have a pilot. It is equipped with an

ignition device which automatically lights the burner. Do not

try to light this burner by hand!!
Before operating smell all around the appliance area for gas. Be

sure to smell next to the floor because propane gas is heavier

than air and will settle to the floor.

CAUTION

WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switches; do not use any

phones in your building.
Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions. If you cannot

reach your gas supplier, call the fire department.

Use only your hand to turn the gas ball valve. Never use tools.

If the valve will not turn by hand, do not try to repair it, call

a qualified service technician. Force or attempted repair may

cause fire or explosion.
Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect the

appliance and to replace any part of the control system and any

gas control which has been under water.

Содержание UTICA BOILERS UB95M-200

















































Результаты поиска

Содержание UTICA BOILERS UB95M-200

Отзывы:

Похожие инструкции для UTICA BOILERS UB95M-200

Бренды по названию

Популярные бренды

ECR UTICA BOILERS UB95M-200, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UTICA BOILERS UB95M-200

Отзывы:

Похожие инструкции для UTICA BOILERS UB95M-200

Бренды по названию

Популярные бренды