ECR UTICA BOILERS UB95M-200 Скачать руководство пользователя

Страница: 15 / 48

figure 9 - Gas piping

The boiler is equipped with a ½” NPT connection on the gas valve

for supply piping and ½” NPT ball valve for manual shut off. The

following rules apply for boiler piping:

Use only those piping materials and joining methods listed

as acceptable by the authority having jurisdiction, or in the

absence of such requirements, by the National Fuel Gas Code,

ANSI Z223.1- latest revision. In Canada, follow the CAN/CGA

B149.1 and .2 Installation Codes for Gas Burning Appliances

and Equipment.

iX - Gas supply pipinG

X - electrical wirinG

iMPORtaNt:

Wiring diagrams for the Gas-Fired Direct Vent Modulating Hot Water Boiler can be

found in Section XIV of this manual.

WARNING

For your safety, turn off electrical power supply at service

panel before making any electrical connections to avoid

possible electric shock hazard. Failure to do so can cause

severe personal injury or death.

NOTICE

IMPORTANT: Wiring must be N.E.C. Class 1. If original

boiler wiring must be replaced, use only type 105°C wire

or equivalent. Boiler must be electrically grounded as re-

quired by National Electrical Code ANSI/NFPA 70 - latest

edition. and operation.

codes

Installations must comply with National Electrical Code, any other

national, state, provincial, or local codes or regulations, and, in

Canada, with CSA C22.1 Canadian Electrical Code (Part 1) and any

local codes. (L1, L2)

line voltage connections

Connect 120 VAC power wiring to line voltage terminal strip

on boiler control panel.
Provide and install a fused disconnect or service switch (15 amp

recommended) as required by code.
Boiler circulator is shipped loose. Wire boiler circulator as

shown in wire diagram label on boiler side panel. (CH L1, CH

L2) CH = Control Heat
When connecting a DHW circulator, connect wiring to line

voltage terminal strip on boiler control panel. (DHW L1, DHW

L2) DHW = Domestic Hot Water

Use pipe joint compound suitable for liquefied petroleum gas

on male threads only.
Use ground joint unions.

Install a sediment trap upstream of gas controls.

Use two pipe wrenches when making the connection to the gas

valve to keep it from turning.
Install a manual shutoff valve in the vertical pipe about 5’ above

floor outside the boiler jacket in addition to the shutoff valve

supplied with the boiler.
Tighten all joints securely.

Propane gas connections should only be made by a licensed

propane installer.
Two stage regulation should be used by the propane installer.

Propane gas piping should be checked out by the propane

10.

installer.

checking the Gas piping

After all connections have been made, check immediately for leaks.

Open the manual shutoff valve. Test for leaks by applying soap suds

(or a liquid detergent) to each joint. Bubbles forming indicate leak.

Correct even the smallest leak at once.

WARNING

Never use a match or open flame to test for leaks!!

Содержание UTICA BOILERS UB95M-200

















































Результаты поиска

Содержание UTICA BOILERS UB95M-200

Отзывы:

Похожие инструкции для UTICA BOILERS UB95M-200

Бренды по названию

Популярные бренды

ECR UTICA BOILERS UB95M-200, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UTICA BOILERS UB95M-200

Отзывы:

Похожие инструкции для UTICA BOILERS UB95M-200

Бренды по названию

Популярные бренды