background image

FCC STATEMENT:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
 1.) This device may not cause harmful interference, and
 2.) This device must accept any interference received, including interference that may cause undesired operation.

WARNING: 

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s 

authority to operate the equipment.

NOTE: 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee 
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures: reorient or relocate the receiving antenna, increase the separation 
between the equipment and receiver, connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected, consult the dealer or an experienced radio/TV technician for help.

RF WARNING STATEMENT:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure 
condition without restriction.

IC STATEMENT:

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
 1.) This device may not cause interference, and 
 2.) This device must accept any interference, including interference that may cause undesired operation of the device.

PRODUCT USE AND PROTECTION:

Read and follow all instructions. Use only as intended.

The ECOXGEAR Bluetooth speaker is intended to be used indoors or outdoors and in land or water environments. The speaker 
has been tested to IP67 waterproofing standards, which means the speaker can be submerged in up to 3 feet of water for 30 
minutes without any damage. However, the speaker is 

NOT

 intended for constant underwater use.

Always make sure the cap(s) / cover(s) are clean, free from sand or debris, and correctly fitted. The speaker will only meet IP67 
ratings if all rubber seals, gasket(s) and cover(s) / cap(s) are in place. If you notice a muffling of audio after submersion, gently 
shake the unit to clear excess water. If your speaker is exposed to salt water, clean it thoroughly after use with fresh water.
The power cable and the unit with an improperly fitted cap are 

NOT

 waterproof.

To prevent fire or shock, do 

NOT

 attempt to charge this unit if it is wet or you suspect water has entered the unit. In this 

situation, please return the unit to Grace Digital for a free assessment. If we have found that the unit has carried water, we will 
repair or replace the unit free of charge.

SAFETY ADVISORY & WARNING:

Read and follow all instructions. Use only as intended.

CAUTION: Do 

NOT

 open to repair. A qualified technician must carry out repair work.

ATTENTION: Do 

NOT

 charge while the unit is wet. Towel dry the unit 

AND

 make sure all connections are dry 

BEFORE 

plugging in the charging connector. Failure to do so may result in electrical damage to the unit and may 

void the warranty.

WARNING:  This product may contain chemicals listed in 

Proposition 65

 

( www.oehha.ca.gov/prop65/prop65_list/Newlist.html )

WARNING:  EcoBoulder has a built-in Lithium battery. The battery must 

NOT

 be used in or near an open heat source or 

excessive heat.

WARNING:  Danger of explosion if battery is incorrectly replaced.
ATTENTION: Do 

NOT

 dispose of in a landfill. Contact Grace Digital at www.gracesupport.com or a certified recycling agent to 

dispose of the unit.

ATTENTION: AC adapter is a device forming a part of the main plug therefore an AC adapter can always be readily 

disconnected from AC socket-outlet.

SAFETY:

This product has a limited life span of use and should be replaced when it shows obvious signs of wear. 
Do not modify or remove any original component parts of the speaker. Doing so could cause damage to the unit, allowing 
water to ingress. A unit with water ingress should not be charged due to potential risk of fire or shock.
Do not attempt to mount the unit except with the approved ECOXGEAR mounts. Doing so could cause damage to the unit 
allowing water to ingress. A unit with water ingress should not be charged due to potential risk of fire or shock.
Please exercise care and good judgment when using your ECOXGEAR speaker. Audio levels should be appropriate to your 
environment, comply with all local regulations, and always ensure that you can hear and be aware of any potential hazards 
around you.

You should always

 1.) Use the ECOXGEAR speaker in accordance with any music or noise rules and regulations.
 2.) Use the proper ECOXGEAR mounts if you intend to mount the unit.
 3.) Properly seal the ECOXGEAR prior and after each use when in humid or water environments to avoid water damage to the 
 

internal components. Salt water / air is particularly corrosive. Always make sure that the gaskets are sealed when in a salt 

 

water environment and that the unit is properly rinsed off after use.

 4.) Properly clean the ECOXGEAR and ensure the gaskets have no sand, dirt, or water on them prior to storage or removing 
 

the back cover.

 5.) Store your unit with all caps properly sealed to avoid long term internal moisture damage inside your unit.
 6.) Completely dry and clean your ECOXGEAR prior to attempting to charge the unit.
 7.) Return the ECOXGEAR to Grace Digital if you suspect water ingress into the unit or if the unit has experienced a severe 
 

impact that may have affected the integrity of the unit to take on water.

You should never

 1.) Never charge your ECOXGEAR if you suspect water has entered the device. Charging a device with water inside could be 
 

potentially hazardous and cause fire or a spark.

 2.) Never use your ECOXGEAR if you have dropped it or thrown it against a hard surface which may have destroyed the 
 

integrity of the speaker, housing, or gaskets. In the event of a severe impact to your unit, please return the unit to Grace  

 

Digital to review for potential damage.

 3.) Never open the auxiliary doors in a water environment. This could cause water to ingress into the unit which could 
 

potentially be hazardous and cause a fire or a spark.

 4.) Never connect a device to the auxiliary input jacks when in a water environment. The auxiliary jacks should only be used in 
 

a dry environment.

 5.) Never attempt to fix, repair your ECOXGEAR unit. Please send it back to Grace Digital for any assessments and repairs.

CARE, MAINTENANCE & PRECAUTIONS:

 1.) The unit is waterproof only when the caps and door are properly closed.
 2.) Close the caps and door properly before use. If the unit is placed in water without the caps or door properly closed, water 
 

may enter into the unit and void your warranty.

 3.) Dry unit completely before opening the caps or door. Do 

NOT

 open the caps or door if wet or in a wet environment.

 4.) Do 

NOT

 apply excessive force to any surfaces of the unit when wet or in a wet environment.

 5.) Do 

NOT

 use or store the unit in places with high temperature.

 6.) 

AVOID

 prolonged exposure to ultraviolet radiation (UV sunlight) and strong magnetic fields.

 7.) Periodically check the rubber seal on the caps and door for premature wear.
 8.) Periodically clean the rubber with a soft moist cloth and ensure no objects such as dirt, hair, sand are on the rubber seal 
 

ring. Do 

NOT

 use any oily solvent or chemicals for cleaning.

 9.) Rinse off the unit with tap water after use in salt water or swimming pool.
10.) Power and / or charge the built-in rechargeable battery for portable use by connecting the AC cord to an AC outlet.
 11.) Noise and audio distortion may occur when the batteries are nearing end of charge.
 12.) Do 

NOT

 remove the built-in battery. Do 

NOT

 remove the grill covers.

LIMITED MANUFACTURER’S WARRANTY:

EcoBoulder is covered by a 3 year limited warranty that covers defects in workmanship and / or materials for a period of 3 
years from original purchase date. This warranty does not apply to any products which have been abused, neglected, modified 
or used for a purpose other than the one for which they were manufactured. Please refer to the above care and maintenance 
instructions for suggested care details. The warranty is valid only for the original owner who purchases the unit from an 
authorized dealer. Transfers do not qualify for warranty protection. Grace Digital reserves the right to replace any out-of-stock 
or discontinued product with a comparable product. Discontinued products may not be available for warranty replacement. 
Any contents are 

NOT

 covered by the limited manufacturer’s warranty. Warranty terms may be revised without notification at 

the discretion of the manufacturer. Please visit www.ecoxgear.com for additional product & warranty information.

EcoBoulder by ECOXGEAR, a division of Grace Digital Inc., San Diego, California. 

Designed in California. Made in China.

U.S. Patent 9,307,307 plus additional Patents Pending.

Содержание EcoBoulder GDI-EXBM900



















Отзывы: