Ecoflam Multiflam 500.1 PR Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 16

background image

pag.11

LB1292

MULTIFLAM 500.1 PR - 600.1 PR

techniques for energy saving

OIL DELIVERY ADJUSTMENT

The diagram illustrates the fuel feeding system of these type of burners, which incorporates a by-pass nozz-
le with oil flow regulation on its return pipe. The oil supply is varied by acting on the nozzle through the
pressure in the return line. Max. oil supply is therefore reached when the pressure in the pump line is
about 30 bar and the return line is fully closed; min. oil supply when the return line is fully open(see also
diagram BERGONZO). Relevant pressure readings in the return line are as follows (return oil pressure has
to be measured on “M” pressure gauge): - max. oil supply : 20 to 30 bar in the pump.

- min. oil supply : 3 to 24 bar in the return.

«
...
9
10
11
12
13
...
»

Содержание Multiflam 500.1 PR

















Отзывы:

Нет отзывов

Похожие инструкции для Multiflam 500.1 PR

Бренд: Jula Страницы: 14

Бренд: Unigas Страницы: 80

Бренд: Honeywell Страницы: 8

Бренд: Honeywell Страницы: 14

Бренд: Honeywell Страницы: 8

MAXON VALUPAK-II 150

Бренд: Honeywell Страницы: 12

SmartValve Q3450A

Бренд: Honeywell Страницы: 8

Hauck MEGASTAR MS-150

Бренд: Honeywell Страницы: 47

Бренд: Honeywell Страницы: 24

Бренд: Honeywell Страницы: 78

Sidekick Smoker

Бренд: FCC Страницы: 14

OpalEscence LDB24B-EN

Бренд: Mason-Lite Страницы: 21

GI MIST 1000 DSPNM-D

Бренд: baltur Страницы: 45

Бренд: baltur Страницы: 96

Бренд: Hotsy Страницы: 18

Бренд: Hotsy Страницы: 30

Бренд: IKEA Страницы: 104

Бренд: Ragalta Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды