Eco House Comfort FHZ1000 страница 69 Скачать руководство пользователя

Страница: 69 / 73

b) Valve operating mechanism

Error Message

Possible cause

Solution

Permanent signal tone and

• The valve is too sluggish

• Remove the valve operating

‘F1’ on the display

or the valve operating mechanism

mechanism

is blocked

• Manually check valve operation
• Mount the valve operating

mechanism again

• If necessary consult a heating

specialist

Permanent signal tone and

• Control range is too large

• Unsuitable valve

‘F2’ on the display

• Valve operating mechanism

• Mount the valve operating

not mounted

mechanism again

• Insert a 1mm thick lug

(for example, a washer) between
the heating valve and
the actuator

Permanent signal tone and

• Control range is too small

• Unsuitable valve

‘F3’ on the display

• Mount the valve operating mecha-

nism again

No radio symbol on the display,

• Loss of radio transmission

• Install control unit at a different

the valve operating mechanism

due to interference

location

emits a tone sequence every hour.

• Control unit batteries

• Replace the batteries

The valve is approx. 30%

are empty

• Transmit the current code

open

• The control unit’s code was

to the valve operating

changed, without

mechanism

synchronising the
valve operating mechanism

Low battery symbol on the display,

• The valve operating mechanism’s

• Replace the batteries

the valve operating mechanism

batteries are empty

emits a tone sequence every
2 minutes for an hour

FHT 8W Heat Demand Relay

Installation and User Guide

Product Code EHC-FH06

Содержание FHZ1000










































































Результаты поиска

Содержание FHZ1000

Отзывы:

Похожие инструкции для FHZ1000

Бренды по названию

Популярные бренды

Eco House Comfort FHZ1000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FHZ1000

Отзывы:

Похожие инструкции для FHZ1000

Бренды по названию

Популярные бренды