Eclipse GEO3.5 Скачать руководство пользователя страница 62

Страница: 62 / 86

62 GEO3.5 MANUAL

SYMPTOM

POSSIBLE CAUSE

SOLUTION

The GEO3.5 does not fire

The micro-switch is not being activated

Adjust the micro-switch activation screw accordingly

The micro-switch is damaged

Replace the circuit board

The PCB is damaged

The solenoid valve is damaged

Replace the solenoid valve

The solenoid valve wires are damaged

The GEO3.5 does not cycle fully

The bolt assembly is dirty or incorrectly lubricated

Clean, re-lubricate and replace the o-rings on the

bolt as necessary

The Dwell parameter is set too low

Increase the Dwell parameter

A sticky or faulty poppet in the solenoid manifold

Check the poppet, clean and replace as necessary

The GEO3.5 is inconsistent

The Dwell parameter is set too low

Increase the Dwell parameter

The Solenoid Flow Restrictor (SFR) is set too low

Increase the flow through the SFR

Using poor quality paintballs

Use better quality paintballs

A poor paintball to barrel bore match

Use a better paintball to barrel bore size match

The inline regulator is supercharging

Strip and clean inline regulator

Dirty body filter

Strip and clean the body filter

Poor / inconsistent air supply into POPS

Use a good quality pre-set air system

The GEO3.5 is inefficient

The Dwell is excessively high

Reduce the Dwell

The GEO3.5 has low rate of fire

The Solenoid Flow Restrictor is set too low

Increase the amount of flow on the SFR

The force setting on the loader is too low

Adjust the loader force feed setting

Содержание GEO3.5























































































Результаты поиска

Содержание GEO3.5

Отзывы:

Eclipse GEO3.5, Руководство пользователя, Страница: 62 / 86

Результаты поиска

Содержание GEO3.5

Отзывы: