Eclipse GEO3.5 Скачать руководство пользователя страница 53

Страница: 53 / 86

GEO3.5 MANUAL 53

MAINTAINING THE SFR

The stages below on SFR maintenance do not require the frame to be removed,

and can be followed for SFR removal/ blanking plug installation.
Using a small hex key push the SFR body out of the left side of the frame

(see

figure 23A)

Inspect and clean the SFR body and o-rings, making sure the hole through the

centre of the SFR body is free of paint or debris

(see figure 23B)

Lastly make sure the pocket in the frame that houses the SFR and the exhaust

port below are clean

(see figure 23C)

Next, insert the SFR body into the frame as shown in

figure 23D

. Make sure the

dial sits flush with the surface of the frame

(see figure 23E)

This last stage of maintenance requires the frame to be removed. It is only need if

the SFR is having little or no effect.
In the top of the frame locate and remove the SFR seal

(see figure 23F)

. Inspect

and clean the seal, replacing if damaged or heavily worn.
Reinsert the SFR seal into the top of the frame, making sure the contoured face is

exposed

(see figure 23G)

WARNING!

Always de-gas your marker, discharging any stored gas in a safe direction,

and remove the barrel, loader, air system and any paintballs to make the

marker easier and safer to work on.
If you are unsure about performing a maintenance procedure please

contact your nearest service centre.

WARNING

FIG 23A

FIG 23C

FIG 23F

FIG 23B

FIG 23D

FIG 23G

FIG 23E

Содержание GEO3.5























































































Результаты поиска

Содержание GEO3.5

Отзывы:

Eclipse GEO3.5, Руководство пользователя, Страница: 53 / 86

Результаты поиска

Содержание GEO3.5

Отзывы: