Eclipse GEO3.5 Скачать руководство пользователя страница 17

Страница: 17 / 86

GEO3.5 MANUAL 17

CONTINUED

Every GEO3.5 comes complete with an Eclipse push on purge system (POPS)

which provides a direct connection for a pre-set air system. Before screwing

an air system into the POPS ensure that the bonnet is disengaged in its forward

position

(see figure 10A)

. If the bonnet is engaged, depress the latch button and

slide the bonnet forward.
Check that the POPS retaining screws are tight. If the POPS can be moved on the

frame the screws are too lose. Use a 5/32” hex key to tighten the screws.
Screw the pre-set air system into the POPS

(see figure 10B)

so that the bottle

screws in all the way and is tight.
Pull the bonnet backwards allowing the POPS pin to depress the valve pin in the

pre-set air system causing the GEO3.5 to become pressurised (providing that

there is sufficient air in your tank)

(see figure 10C)

. When the bonnet has been

pulled back far enough it engages with the POPS body.

1,2

You have now installed a pre-set air system onto your GEO3.5.

1 High, mid and low pressure output pre-set air systems can be used with the GEO3.5, providing

the GEO3.5 has the SL4 inline regulator originally supplied with the marker.

2 The force needed to engage the bonnet may vary depending on the output pressure and internal

design of the air system being used.

FIG 10A

FIG 10B

FIG 10C

Содержание GEO3.5























































































Результаты поиска

Содержание GEO3.5

Отзывы:

Eclipse GEO3.5, Руководство пользователя, Страница: 17 / 86

Результаты поиска

Содержание GEO3.5

Отзывы: