Eclipse GEO3.5 Скачать руководство пользователя страница 32

Страница: 32 / 86

32 GEO3.5 MANUAL

SEMI SHOTS PARAMETER

The parameter sets the number of shots in semi-automatic that are required at the KICK IN rate before ramping will start.

The parameter can be set between 3 and 9 pulls in 1 pull increments.

KICK IN PARAMETER

This parameter sets the minimum rate at which the user has to pull the trigger in order to start ramping. This parameter can

be set between 3.3 and 10.0 pulls per second in 0.1 pulls per second increments.

SUSTAIN PARAMETER

Once the GEO3.5 is ramping the user has to continue to pull the trigger at a minimum rate in order to maintain the ramping.

This parameter sets this rate and can be between 3.3 and 10.0 pulls per second in 0.1 pulls per second increments.

RESTART PARAMETER

The RESTART parameter defines the amount of time after the last trigger pull during which the ramp can be restarted with a

single trigger pull. If a trigger pull occurs after the RESTART time has expired, then the other ramp start conditions have to

be met before ramping will restart. This parameter can be set between 0.0 and 1.0 seconds in 0.1 second increments.

Содержание GEO3.5























































































Результаты поиска

Содержание GEO3.5

Отзывы:

Eclipse GEO3.5, Руководство пользователя, Страница: 32 / 86

Результаты поиска

Содержание GEO3.5

Отзывы: