Eclipse GEO Скачать руководство пользователя страница 25

Страница: 25 / 43

rEl TM

ThE rElEasE TiME paraMETEr

the

rEl TM

parameter is used to set the minimum

amount of time that the trigger must be released

before it is recognised as a valid trigger release.

this parameter can be set between 3.0 and 25.0

milliseconds in 0.1 ms increments.

pUll pT

ThE pUll pOiNT paraMETEr

the

pUll pT

parameter is only available if

OpTO

has

been selected in the hardware menu.

pUll pT

defines

the point at which the trigger is considered pulled and

is adjustable between 51% and 99% in 1% increments.

FUll

ThE FUll paraMETEr

tumbling paintballs can take time to settle in the

breech before they can be successfully fired. this

parameter is used to set the amount of time that a

paintball has to be in the breech before the Geo is

allowed to fire. this parameter can be set between 1.0

and 20 milliseconds in 0.5ms increments.

pUll TM

ThE pUll TiME paraMETEr

the

pUll TM

parameter is used to set the minimum

amount of time that the trigger must be pulled before

it is recognised as a valid trigger pull. this parameter

can be set between 1.0 and 20.0 milliseconds in 0.5 ms

increments.

-U

48.

CONTENTS

ORIENTATION

QUICK SET-UP

USING YOUR GEO

ADVANCED SET-UP

MENU TREE

MAINTENANCE

FAULT FINDING

SERVICE CENTERS

PARTS LIST

SPARES & ACCESSORIES

49.

-U

ADVANCED SET-UP

QUicK gUidE

Содержание GEO












































Результаты поиска

Содержание GEO

Отзывы:

Похожие инструкции для GEO

Бренды по названию

Популярные бренды

Eclipse GEO, Руководство оператора

Результаты поиска

Содержание GEO

Отзывы:

Похожие инструкции для GEO

Бренды по названию

Популярные бренды