Eclipse GEO Скачать руководство пользователя страница 23

Страница: 23 / 43

lighT

ThE lighT paraMETEr

the lcd backlight is illuminated whenever any of the

buttons are pressed on the Geo. the

lighT

parameter

is used to set the amount of time that the backlight

stays lit between 0.0 and 20.0 seconds in 0.5 second

increments.

slEEp

ThE slEEp paraMETEr

if the Geo is inactive for a period of time then it will

automatically switch off in order to save power. the

slEEp

parameter is used to set that time between 5 and

60 minutes in 5 minute increments.

TiMiNg

ThE TiMiNg MENU

the parameters on the timing menu all relate to the

timing of specific events.

dwEll

ThE dwEll paraMETEr

the

dwEll

parameter sets the amount

of time that the solenoid is energized

and therefore the amount of air that

is released with each shot of the Geo.

setting this parameter too low will result

in low velocity shots and/or excessive

shot to shot velocity fluctuations.

setting the parameter too high will

simply waste gas and make the Geo

louder.

the

dwEll

can be set between 0.0 and

25.0 milliseconds. the factory default

setting can normally be reduced after a

few thousand shots as the Geo ‘beds-in’.

Fsd cOMp

ThE FirsT shOT drOp-OFF cOMpENsaTiON

paraMETEr

first shot drop off is a reduction in

velocity of the first shot fired after an

extended period of not firing and is

caused by the stiction between dynamic

o-rings and the surfaces that they are

in contact with. in order to compensate

for fsd this parameter can be set to add

extra time to the

dwEll

parameter for

the first shot. this parameter can be set

between 0.0 and 5.0 milliseconds.

Fsd dlY

ThE FirsT shOT drOp OFF dElaY paraMETEr

this parameter sets the amount of time

after the last shot before the

Fsd cOMp

is used on the next shot. the first shot

after powering on the Geo will always

have

Fsd cOMp

this parameter can be

set between 30 and 240 seconds in 10

second increments.

-U

44.

CONTENTS

ORIENTATION

QUICK SET-UP

USING YOUR GEO

ADVANCED SET-UP

MENU TREE

MAINTENANCE

FAULT FINDING

SERVICE CENTERS

PARTS LIST

SPARES & ACCESSORIES

45.

-U

ADVANCED SET-UP

QUicK gUidE

Содержание GEO












































Результаты поиска

Содержание GEO

Отзывы:

Похожие инструкции для GEO

Бренды по названию

Популярные бренды

Eclipse GEO, Руководство оператора

Результаты поиска

Содержание GEO

Отзывы:

Похожие инструкции для GEO

Бренды по названию

Популярные бренды