background image

G

RASS

 T

RIMMER

/B

RUSH

 C

UTTER

O

PERATOR

'

S

 M

ANUAL

7

SAFE

 

OPERATION

WARNING  

  DANGER

Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can
cause serious injury or death.

• Provide all operators of this equipment with the Operator's Manual

and instructions for safe operation.

Keep A Firm Grip
• Hold the front and rear handles with both hands with thumbs and

fingers encircling the handles

Keep A Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery,

uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.

E

MISSION

 C

ONTROL

 --

The emission control system for this engine is EM (Engine
Modification).

IMPORTANT ENGINE INFORMATION
ENGINE FAMILY:  TEH024UB24RC
DISPLACEMENT:  23.6 CC
THIS ENGINE MEETS U.S. EPA PH1 AND 1996
- 1999 CALIFORNIA EMISSION REGULATIONS
FOR ULGE ENGINES. REFER TO OWNER'S
MANUAL FOR MAINTENANCE SPECIFICA-
TIONS AND ADJUSTMENTS.

Emission Control Label located on Engine
(EXAMPLE ONLY, information on label varies by FAMILY).

D

ESCRIPTION

The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions,
shield installation and other assembly may be necessary.

After opening the carton, check for damage.  Immediately notify your retailer or ECHO Dealer of damaged or missing
parts.  Use the contents list to check for missing parts.

Содержание SMR-2100





































Отзывы: