background image

2

D

WARNING  

  DANGER

Inspect starting area for hazards such as rocks, glass, debris etc. which
could be contacted by the cutting attachment when starting. Keep
helpers and bystanders at least 15 m (50 ft.) from starting area, other-
wise serious personal injury may result.

4.

Lay the pruner on a flat clear area. Firmly grasp right hand grip and
throttle trigger lockout with left hand and fully depress throttle trigger
to wide open position. Rapidly pull recoil starter handle/rope (D) until
engine fires (or maximum five [5] pulls).

5.

After engine fires (or five [5] pulls), move choke lever back to “Run”
position. Hold throttle trigger and throttle trigger lockout fully de-
pressed and pull recoil starter handle/rope until engine starts and runs.
Release throttle trigger and allow unit to warm up at idle for several
minutes.

NOTE
If engine does not start with choke in “Run” position after 5 pulls, repeat
instructions.

6.

After engine warm up, gradually depress throttle trigger to increase
engine RPM to operating speed.

STARTING

 

WARM

 

ENGINE

The starting procedure is the same as Cold Start except DO NOT close the
choke.

WARNING  

  DANGER

The cutting attachment should not move at idle. If cutting attachment
moves, readjust carburetor according to "Carburetor Adjustment"
instructions in this manual or see your ECHO Dealer, otherwise serious
personal injury may result.

1.

Stop Switch - Start/Run.  Move Stop Switch button  (A) forward away
from the STOP position.

2.

Start - Pull Rope.  Lay the pruner on a flat clear area and  pull the recoil
starter handle (D) until the engine fires.

A

    NOTE
    If engine does not start after 5 pulls, use Cold Start Procedure.

STOPPING

 

ENGINE

1.

Release Throttle.  Allow engine to return to idle before shutting engine
off.

2.

Stop Switch - Stop.  Move stop switch button (A) backward to STOP
position.

WARNING  

  DANGER

If engine does not stop when stop switch is moved to STOP position,
close choke - COLD START position - to stall engine. Have your ECHO
dealer repair stop switch before using trimmer again.

A

NOTE
Refer to the attachment Operator's
Manual and Safety Manual (if included)
for proper and safe operating tech-
niques.

Содержание SMR-2100





































Отзывы: