background image

S

ERVICING

 I

NFORMATION

PARTS

Genuine ECHO Parts and ECHO Re Power Parts and Assemblies for
your ECHO products are available only from an Authorized ECHO
Dealer.  When you do need to buy parts always have the Model
Number, Type number and Serial Number of the unit with you.  You can
find all three numbers on the engine housing.  For future reference, write
them in the space provided below.

Model No. ____________ Type No. ____________ SN. __________

SERVICE

Service of this product during the warranty period must be performed
by an Authorized ECHO Service Dealer.  For the name and address of
the Authorized ECHO Service Dealer nearest you, ask your retailer or
call:  1-800-432-ECHO (3246) When presenting your unit for Warranty
service/repairs, proof of purchase is required.

ECHO

 

CONSUMER

 

PRODUCT

 

SUPPORT

If you require assistance or have questions concerning the application,
operation or maintenance of this product, you may call the ECHO
Consumer Product Support Department at 1-800-673-1558 from 8:30 am
to 4:30 pm (Central Standard Time) Monday through Friday. Before
calling, please know the model and serial number of your unit to help
your Consumer Product Support Representative.

WARRANTY

 

REGISTRATION

You may register your Echo equipment using the warranty registration
card or register on-line at www.echo-usa.com. Registering provides a
direct link between you and ECHO if we find it necessary to contact
you.

ADDITIONAL

 

OR

 

REPLACEMENT

 

MANUALS

Safety Manuals  in English/Spanish or English/French are available, free of charge, from your ECHO dealer or at
www.echo-usa.com.
Operator's and Parts Manuals are available by:
• Downloading free from www.echo-usa.com
• Purchasing from your Echo Dealer.
• Sending a check or money order for $2.00 per Parts Catalog or $1.50 per Operator's Manual made payable to ECHO,

INCORPORATED.  State on a sheet of paper the model number and serial number of the ECHO unit you have, part
number of the manual (if known), your name and address, and mail to address below.

Safety Videos are available from your Echo dealer. A $5.00 shipping charge is required for each video.

Available Parts Catalog Parts Lists

SRM-2100/2110 TYPE 1E S/N 001001 & UP

PART NUMBER 99922202674

ECHO, INCORPORATED

400 O

AKWOOD

 R

OAD

L

AKE

 Z

URICH

, IL  60047

www.echo-usa.com

DEALER?

CALL

1-800-432-ECHO

OR

www.echo-usa.com

CONSUMER PRODUCT

SUPPORT

1-800-673-1558

8:30 - 4:30 MON - FRI C.S.T.

Содержание SMR-2100





































Отзывы: