Echo SHC-2401 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 28

background image

4

DECALS

Locate these safety decals on your unit. The complete unit illustration found in the "DESCRIPTION" section, will help
you locate them. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal
cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific
information.

DRIVE SHAFT DECALS

Symbol

description/application

Symbol form/shape

Symbol

description/application

Symbol form/shape

Hot

Surface

Carburetor adjustment

- Idle speed

Carburetor adjustment

- High speed mixture

Symbol

description/application

Symbol form/shape

Symbol

description/application

Symbol form/shape

Read and understand

Operator's Manual.

Wear eyes, ears and

head protection

Emergency stop

Fuel and oil mixture

Finger Severing

Hazard

Carburetor adjustment

- Low speed mixture

Safety/Alert

Do not operate clos-

er than 15 M (50 ft.)

from electrical

hazards.

Keep bystanders at

least 15 meters

(50 feet) away.

Wear hand

protection. Use

two handed.

DO NOT smoke

near fuel.

DO NOT allow

flames or sparks

near fuel.

Wear slip resistant

foot wear.

Engine choke

control.

Ignition

ON/OFF

Primer bulb

Avoid all power lines.

This unit is not insulat-

ed against electrical

current.

INTERNATIONAL

SYMBOLS

«
...
2
3
4
5
6
...
»

Содержание SHC-2401





























Отзывы:

Нет отзывов

Похожие инструкции для SHC-2401

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: DARAY Страницы: 24

Бренд: Walker Страницы: 24

Бренд: Rapid Technic Страницы: 152

Бренд: GALBIATI Страницы: 8

AquaPure Ei Series

Бренд: Jandy Страницы: 4

AquaPure Ei Series

Бренд: Jandy Страницы: 8

Jandy Pro Series

Бренд: Jandy Страницы: 16

Бренд: Pani Страницы: 12

Бренд: FASTER TOOLS Страницы: 19

Бренд: JBM Страницы: 12

Portable Vocal Booth Pro Studio Series

Бренд: EditorsKeys Страницы: 2

Calculite C6P38MHA

Бренд: Lightolier Страницы: 2

Бренд: Williams Sound Страницы: 32

Бренд: GREAT PLAINS Страницы: 190

Бренд: GE Страницы: 2

Бренд: Patlite Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды