Echo SHC-2401 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 28

background image

12

S

PECIFICATIONS

MODEL

SHC-2401

Length

2190 mm (86.3 in.)

Width

216 mm (8.5 in.)

Height

229 mm (9.0 in.)

Weight (dry)

5.7 kg (12.6 lb.)

Engine Type

Air cooled, two-stroke, single cylinder gasoline engine

Bore

34.0 mm (1.34 in.)

Stroke

26.0 mm (1.04 in.)

Displacement

23.6 cc (1.44 cu. in.)

Exhaust

Spark Arrestor Muffler

Carburetor

Walbro diaphragm model WT w/primer

Ignition System

Flywheel magneto, capacitor discharge ignition with ESG

Spark Plug

NGK BPM-7Y (Gap 0.65 mm (0.026 in.)

Fuel

Mixed (Gasoline and Two-stroke Oil)

Fuel/Oil Ratio

50:1 ECHO High Performance, two-stroke air cooled engine oil

Gasoline

89 Octane unleaded. DO NOT use fuel containing methyl alcohol, more than

10% ethyl alcohol or 15% MTBE.

Oil

50:1 ECHO High Performance, two-stroke air cooled engine oil

Fuel Tank Capacity

0.4 lit. (14.0 US fl. oz.)

Recoil Starter System

Automatic Recoil Starter

Clutch

Centrifugal Type

Gear Case Ratio

6.36:1 Reduction

Cutter

Length

Pitch

Double Reciprocating Blade - Double Edge

524 mm (20.5 in.)

35 mm (1.4 in.)

Idle Speed

2800 - 3200 RPM

Wide Open Throttle Speed (W.O.T.)

8000 - 10000 RPM

«
...
10
11
12
13
14
...
»

Содержание SHC-2401





























Отзывы:

Нет отзывов

Похожие инструкции для SHC-2401

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: TC Electronic Страницы: 6

Бренд: RainPoint Страницы: 40

Бренд: FARM-MAXX Страницы: 35

Бренд: Qtx Страницы: 6

Бренд: Beta Страницы: 8

Бренд: RayLight Страницы: 31

Бренд: PLUSLITE Страницы: 13

RIDA qLine Scan

Бренд: R-Biopharm Страницы: 24

Бренд: Z-CAM Страницы: 45

AQUAvalve5 1Pot

Бренд: Autopot Страницы: 2

Бренд: Omni Страницы: 20

Бренд: North Star Страницы: 10

Бренд: dosatron Страницы: 19

Бренд: Yardworks Страницы: 7

Бренд: Raymarine Страницы: 76

Бренд: Yacht Sentinel Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды