Echo SHC-2401 Скачать руководство пользователя страница 25

Страница: 25 / 28

HAFT

EDGE

LIPPER

PERATOR

ANUAL

Drive Shaft Assembly

NOTE
Hedge Clipper drive shaft should be greased every 25 hours of
operation.

Tools required: 8MM Open End Wrench, Screwdriver, Clean Rag,
Small Brush.

Parts required: High Temperature Grease P/N 91014

WARNING DANGER

Blades are very sharp. Wear gloves to protect hands, otherwise
serious personal injury may result.

Loosen gear box locating screw (A) and mounting screws (C).
Remove the gear box from the drive shaft housing.

Pull the drive shaft (B) from the housing, wipe clean and re-coat
with a thin coating [1/2 oz. (15 ml)] of high temperature grease.

Slide the flexible shaft back in the drive housing being careful not
to get dirt on the flex shaft.

Install the gear box assembly.

SHARPENING

BLADES

Level 2.
Tools required: Flat file, Small Screwdriver

Parts required:

None

NOTE
Hedge Clipper Blades are very sharp. Wear gloves to protect
hands.

Use screwdriver to separate upper and lower cutters equal distance
apart.

File each edge carefully. Follow the original shape of the blade.

IMPORTANT
If a power grinder is used DO NOT allow blade to over heat.

Lubricate blades. See "Blade Lubrication Instructions", page 24
this section.

Содержание SHC-2401





























Результаты поиска

Содержание SHC-2401

Отзывы:

Похожие инструкции для SHC-2401

Бренды по названию

Популярные бренды

Echo SHC-2401, Руководство оператора

Результаты поиска

Содержание SHC-2401

Отзывы:

Похожие инструкции для SHC-2401

Бренды по названию

Популярные бренды