dosatron D14MZ10 Скачать руководство пользователя страница 1

Страница: 1 / 19

Page 1

800-523-8499

www.dosatronusa.com

Proper protection, such as gloves, eye wear, and aprons, are recommended when disassembling a Dosatron.

Step 3:

Check to see if you feel suction on your finger.

Step 2:

If there is still no suction, but the Dosatron unit is clicking,

turn the water on. Unscrew and remove the suction hose nut or

clamp and hose.

D14MZ10 Troubleshooting - Part 1

This D14MZ10 - 14 GPM Troubleshooting - Part 1 will cover: The Injector is

not drawing the concentrate, but is

clicking.

Scan the QR code to

watch our D14MZ10 -

Troubleshooting video.

Step 1:

Take a look at the strainer. If it is clogged just clean it out

and retest your Dosatron unit.

NOTE:

To service your D14MZ10 you will need a strap wrench

(Part #: TOOL01) and a small flat head screw driver.

Содержание D14MZ10




















Результаты поиска

Содержание D14MZ10

Отзывы:

Похожие инструкции для D14MZ10

Бренды по названию

Популярные бренды

dosatron D14MZ10, Руководство по устранению неисправностей

Результаты поиска

Содержание D14MZ10

Отзывы:

Похожие инструкции для D14MZ10

Бренды по названию

Популярные бренды