Echo SC-4213 Скачать руководство пользователя

Страница: 6 / 32

3 INCH CHIPPER/SHREDDER

SAFETY

1. Always stand clear of discharge area when operating

this machine. Keep face and body away from feed

and discharge openings.

2. Keep hands and feet out of feed and discharge

openings while machine is operating to avoid serious

personal injury. Stop and allow

machine to come to a complete

stop before clearing obstructions.

3. Set up your work site so you are

not endangering traffic and the

public. Take great care to provide

adequate warnings.

4. Do not climb on machine when operating. Keep

proper balance and footing at all times.

5. Check cutting chamber to verify it is empty before

starting the machine.

6. The rotor will continue to rotate after being disengaged.

Shut off the machine and make sure all moving parts

have come to a complete stop before inspecting or

servicing any part of the machine. Disconnect the

battery and remove the ignition key if applicable.

7. Do not insert branches with a diameter larger than

the max chipper capacity into machine or machine

damage may occur.

8. When feeding material into machine, do not allow

metal, rocks, bottles, cans or any other foreign

material to be fed into the machine.

Ensure debris does not blow into traffic, parked cars,

or pedestrians.

10. Keep the machine clear of debris and other

accumulations.

11. Do not allow processed material to build up in the

discharge area. This may prevent proper discharge

and can result in kickback of material through the

feed opening.

12. If the machine becomes clogged, the cutting

mechanism strikes any foreign object, or the machine

starts vibrating or making an unusual noise, shut off

machine immediately and make sure all moving parts

have come to a complete stop. Disconnect the battery

and remove the ignition key if applicable. After the

machine stops: A) Inspect for damage, B) Replace

or repair any damaged parts, and C) Check for and

tighten any loose parts.

13. On electric start models, disconnect cables from

battery before doing any inspection or service.

Remove key.

14. Check blade bolts for proper torque after every 8 hours

of operation. Check blades and rotate or resharpen

daily or as required to keep blades sharp. Failure

to do so may cause poor performance, damage or

personal injury and will void the machine warranty.

8. Do not allow children to operate this equipment.
9.

Use only in daylight or good artificial light.

10. Do not run this equipment in an enclosed area. Engine

exhaust contains carbon monoxide gas, a deadly

poison that is odorless, colorless and tasteless.

Do not operate this equipment in or near buildings,

windows or air conditioners.

11. Always use an approved fuel container. Do not

remove gas cap or add fuel when engine is running.

Add fuel to a cool engine only.

12.

Do not fill fuel tank indoors. Keep open flames, sparks,

smoking materials and other sources of combustion

away from fuel.

13. Do not operate machine without shields in place.

Failure to do so may cause serious injury or death.

14.

Keep all guards, deflectors, and shields in good

working condition.

15. Before inspecting or servicing any part of this machine,

shut off the machine and make sure all moving parts

have come to a complete stop. Disconnect the battery

and remove the ignition key where applicable.

16. Check that all screws, nuts, bolts, and other fasteners

are secured, tightened and in proper working condition

before starting the machine.

17. Do not transport or move machine while it is operating

or running.

1.4 OPERATION SAFETY

1. Before inspecting, servicing, storing, or changing

an accessory, shut off the machine and make sure

all moving parts have come to a complete stop.

Disconnect the battery and remove the ignition key

where applicable.

2. Replace any missing or unreadable safety decals.

Refer to the safety decal section for part numbers.

3. Allow machine to cool before storing in an enclosure.
4. Store the machine out of reach of children and where

fuel vapors will not reach an open flame or spark.

5. Never store this machine with fuel in the fuel tank

inside a building where fumes may be ignited by

an open flame or spark. Ignition sources can be hot

water and space heaters, furnaces, clothes dryers,

stoves, electric motors, etc.

6. Drain the fuel and dispose of it in a safe manner for

storage periods of three months or more.

1.5 MAINTENANCE/STORAGE SAFETY

Содержание SC-4213

































Результаты поиска

Содержание SC-4213

Отзывы:

Похожие инструкции для SC-4213

Бренды по названию

Популярные бренды

Echo SC-4213, Руководство оператора

Результаты поиска

Содержание SC-4213

Отзывы:

Похожие инструкции для SC-4213

Бренды по названию

Популярные бренды