Power (On/Off) switch contro(Blue)
Jam indicator l(Red)
Bin-out indicator (Blue)
Safe touch(Red)
Over-heat indicator Blue)
Bin-full indicator (
Red
)
Reverse switch control
Forward switch control
CAPACITY
Model No.
HS-1225M
HS-1826C
Security level
DIN 4
DIN 3
Paper cut size ( mm )
2 X 8
4X35
Paper shred capacity ( A4 70g)
12
18
CD/ Credit card shred
One pc per time
One pc per time
Shred:
Paper, credit cards, CD/DVD’s, staples and paper clips ( length
≤
3cm)
Cann’t shred:
Adhesive labels, cardboard, soft disk, laminates, document clips, X-film and other plastic than noted above
Paper Entry Width: 230mm
Unload motor power 230W,power at capacity 500W ; heavier, humidity or other than rated voltage may reduce capacity.
Recommended daily usage rates: 20-50 paper passes; 50 credit cards; 5 CDs
Environmental requirement: Temperature operating range to be 10˚C – 26˚C / 50˚F – 80˚F and 40-80% Relative humidity
WARNING: IMPORTANT SAFETY INSTRUCTIONS—READ BEFORE USING!
This Machine has a disconnect switch , it must be in ON (I) position to operate shredder. If urgent thing happens,
must switch to OFF (O) position to stop shredding.
Avoid touching exposed blades under Cross-cut shredder head.
If remove the shredder usually, can assemble four casters onto the caster holes under the bottom before use.
( casters are removable).
Don’t put cann’t shred objective on the entry.
Use only designated entry for CDs. Keep finger away from CD entry.
The grounded socket-outlet shall be installed near the equipment and shall be easily accessible.
OPERATION
Plug in and set to ON ( I ), machine can work.
Continuous work: 30 minutes
Note
: Shredder runs briefly after each pass to clear entry. Continuous operation beyond 10 minutes will trigger a cool
down period to resume operation.
MAINTENANCE AND TROUBLESHOOTING
For best performance, oil each time when bin is full.
Note:
Only use a non-aerosol vegetable oil;
Without oil, may cause lower shredding efficiency, noise, even cann’t work normally.
Reverse the shredder 15 seconds to clean the cutter every day.
Clean up the pull-out bin when bin-full indicator illuminates.
When the pull-out bin is not in correct position, or bin is full, the motor will be disabled.
The Overheat indicator will illuminate when the motor reaches the thermal cut out temperature, then it will take 30
minutes for cool down.
WARRANTY
We warrants the cutting blades of the machine to be free from defects in material and workmanship for 5 years from the
date of purchase by the original consumer.
We warrants all other parts of the machine to be free of defects in material and workmanship for 1 year from the date of
purchase by the original consumer.
If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or
replacement, at our option and expense, of the defective parts. This warranty does not apply in cases abuse, mishandling,
or unauthorized repair.
Any implied warranty, including that of merchantability or fitness for a particular purpose, is hereby limited in duration to
the appropriate warranty period set forth above. In no event shall be liable for any consequential or incidental damages
attributable to this product.
This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide,
except where different limitations, restrictions, or conditions may be required by local law.
For more details or to obtain service under this warranty, please contact us or your dealer.
Keep away from children and pets. Keep hands away from paper entry.
Always set to off or unplug when not in use..
Keep foreign objects such as gloves, jewelry, clothing, hair, etc. away from shredder
openings. If object enters top opening, switch to Reverse (
) to back out object.
Never use aerosol, petroleum based or other flammable products on or near
shredder. Do not use canned air on shredder.
Stop using broken or defected shredder. Do not disassemble shredder. Never put
shredder near by hot source or water.
