manualshive.com logo in svg

Echo PPFD-2400 TYPE 1/1E, Руководство оператора

Поделиться
Скачать
Echo PPFD-2400 TYPE 1/1E Скачать руководство пользователя страница 33

P

OWER

 P

RUNER

O

WNER

'

S

 M

ANUAL

33

S

TORAGE

Long Term Storage (over 30 days)

Do not store your unit for a prolonged period of time (30 days or longer)
without performing protective storage maintenance which includes the
following:

1. Store unit in a dry, dust free place, out of the reach of children.

WARNING           DANGER

Do not store in enclosure where fuel fumes may accumulate or
reach an open flame or spark or serious personal injury may result.

2. Move stop switch button (A) backward to STOP position.

3. Remove accumulation of grease, oil, dirt and debris from exterior of

unit.

4. Perform all periodic lubrication and services that are required.

5. Tighten all the screws and nuts.

6. Drain the fuel tank completely and pull the recoil starter handle

several times to remove fuel from the carburetor.

7. Remove the spark plug and pour 30 ml of fresh, clean, two-stroke

engine oil into the cylinder through the spark plug hole.

A. Place a clean cloth over the spark plug hole.
B. Pull the recoil starter handle 2-3 times to distribute the oil inside

the engine.

C. Observe the piston location through the spark plug hole.  Pull

the recoil starter handle slowly until the piston reaches the top of
its travel and leave it there.

8.

Install the spark plug (do not connect spark plug cable).

9.

Install guide bar cover on guide bar and saw chain during storage.

A

Содержание PPFD-2400 TYPE 1/1E



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды