manualshive.com logo in svg

Echo PPFD-2400 TYPE 1/1E, Руководство оператора

Поделиться
Скачать
Echo PPFD-2400 TYPE 1/1E Скачать руководство пользователя страница 24

24

SPARK

 

PLUG

Level 2.

Parts Required: Spark Plug, NGK  BPM-7Y

1. Remove spark plug and check for fouling, worn and rounded center

electrode.

2. Clean the plug or replace with a new one.  DO NOT sand blast to

clean. Remaining sand will damage engine.

3. Adjust spark plug gap by bending outer electrode.

4. Tighten spark plug to 145-155 kg-cm (125-135 in. lb.).

0.65 mm

(0.026 in.)

COOLING

 

SYSTEM

 

CLEANING

Level 3.

Parts Required:  None.

IMPORTANT
To maintain proper engine operating temperatures, cooling air
must pass freely through the cylinder fin area. This flow of air
carries combustion heat away from the engine.

Overheating and engine seizure can occur when:

•

Air intakes are blocked, preventing cooling air from reaching the
cylinder.

•

Dust and grass build up on the outside of the cylinder. This build
up insulates the engine and prevents the heat from leaving.

Removal of cooling passage blockages or cleaning of cooling fins is
considered “Normal Maintenance”. Any failure attributed to lack of
maintenance is not warranted.

1.

Remove spark plug lead from spark plug and throttle linkage end
from the carburetor swivel.

2.

Remove the four screws that retain the engine cover (A). Two at
the top of the recoil starter, two on either side of the front. Lift the
cover from the engine and lay to the front of the Power Pruner.

NOTE
The throttle linkage remains assembled to the engine cover and the
spark plug lead and grommet remain installed.

A

A

Содержание PPFD-2400 TYPE 1/1E



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды