manualshive.com logo in svg

Echo PPFD-2400 TYPE 1/1E, Руководство оператора

Поделиться
Скачать
Echo PPFD-2400 TYPE 1/1E Скачать руководство пользователя страница 12

12

1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter.

2. REAR HANDLE ASSEMBLY WITH THROTTLE TRIGGER LOCKOUT - Sturdy handle for right hand placement.

Includes stop switch, throttle trigger and throttle trigger lockout.

3. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. The engine does not stop when throttle

trigger lockout lever is released and throttle trigger is engaged during throttle operation. Operation of the throttle
trigger is prevented unless throttle trigger lockout lever is engaged.

4.  STOP SWITCH - Mounted on top of rear handle assembly.  Move switch forward to run, back to stop.

5. THROTTLE TRIGGER - Spring loaded to return to idle when released.  During acceleration press throttle trigger

gradually for best operating technique.

6. SHOULDER HARNESS - An adjustable strap that suspends the unit from the operator.

7. SHAFT TUBE - Durable fiberglass mesh housing.

8. AUTOMATIC OILER - Self oiling. Use high quality, low viscosity, non detergent guide bar and saw chain oil.

9. SAW CHAIN - 91 VS  9.53 mm (3/8") low profile Oregon saw chain. Runs approximately 609.6 m/min (2000 ft/min) at

full throttle.

10. GUIDE BAR - 305 mm (12 inch) Guide Bar.

11. CUTTING SHOE - Used to capture and stabilize branch while cutting.  Place cutting shoe against branch, accelerate

and lower saw chain into branch.

12. CUTTING ATTACHMENT - Sealed, gear ratio is 1.5:1 reduction.

13. MUFFLER, SPARK ARRESTER - The muffler controls the exhaust noise while the spark arrestor prevents hot,

glowing particles of carbon from leaving the muffler where they could possibly start a fire.

14. RECOIL STARTER - Pull handle slowly until recoil starter engages, then quickly and firmly. When engine starts

return handle slowly.  DO NOT let handle snap back or damage will occur.

15. FUEL TANK - Contains fuel and fuel filter.

16. FUEL TANK CAP - Covers and seals fuel tank opening.

17. PRIMER BULB - Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the carbure-

tor for starting.  Pump the bulb 10 times until fuel is visible in clear fuel return line.

18. AIR CLEANER ASSEMBLY - Contains replaceable air filter element.

19. CHOKE - Located above air cleaner housing.  Controls operation of choke. Move lever to starting position (Close

Choke) and back to run position (Open Choke).

20. SPARK PLUG - Provides spark to ignite fuel mixture.

21. ARM REST  - Provides arm rest during operation and protects arm from hot engine.

22. OPERATORS MANUAL - Read and understand this manual before operation. Keep manual in a safe location for future

reference, i.e., operation, maintenance, storage and specifications.

Содержание PPFD-2400 TYPE 1/1E



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды