background image

PAS R

APID

 L

OADER

TM

 T

RIMMER

 A

TTACHMENT

O

PERATOR

'

S

 M

ANUAL

3

Symbol

description/application

Symbol form/shape

Symbol

description/application

Symbol form/shape

Hot

Surface

Carburetor adjustment

- Idle speed

Carburetor adjustment

- High speed mixture

Symbol

description/application

Symbol form/shape

Symbol

description/application

Symbol form/shape

Read and understand

Operator's Manual.

Wear eyes, ears and

head protection

Emergency stop

Fuel and oil mixture

Finger Severing

Carburetor adjustment

- Low speed mixture

Safety/Alert

Avoid all power

lines. This unit is

not insulated

against electrical

current.

Do not operate

closer than 15 M

(50 ft.) from

electrical

hazards.

Keep bystanders

at least 15 meters

(50 feet) away.

Plan retreat path

from falling

objects.

Wear hand

protection. Use

two handed.

DO NOT smoke

near fuel.

DO NOT allow

flames or sparks

near fuel.

Wear slip

resistant foot

wear.

Ignition

ON/OFF

Primer bulb

Keep bystanders and helpers

away 15 m (50 ft.).

Choke Control

"Cold Start"

Position

(Choke Closed)

Choke Control

"Run"

Position

(Choke Open)

INTERNATIONAL

 

SYMBOLS

IMPORTANT  The enclosed message
provides information necessary for the
protection of the unit.

NOTE  This enclosed message provides tips for
use, care and maintenance of the unit.

This symbol accompanied by the words  WARNING and
DANGER calls attention to an act or condition that can lead
to serious personal injury to operator and bystanders.

The circle with the slash symbol means whatever is shown
within the circle is prohibited.

S

AFETY

MANUAL

 

SAFETY

 

SYMBOLS

 

AND

 

IMPORTANT

 

INFORMATION

Throughout this manual and on the product itself, you will find safety
alerts and helpful, information messages preceded by symbols or key
words.  The following is an explanation of those symbols and key words
and what they mean to you.

IMPORTANT

NOTE

PERSONAL

 

CONDITION

 

AND

 

SAFETY

 

EQUIPMENT

WARNING  

  DANGER

Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly
or safety precautions are not followed.  Proper clothing and safety gear must be worn when operating a
trimmer/brush cutter.

Содержание PAS-260/261

















Отзывы: