background image

PAS R

APID

 L

OADER

TM

 T

RIMMER

 A

TTACHMENT

O

PERATOR

'

S

 M

ANUAL

7

C

ONTENTS

After opening the carton, check for damage.  Immediately notify your retailer or ECHO Dealer of damaged or missing
parts.  Use the contents list to check for missing parts.

__ 1 - Pro Attachment Series

TM

 Trimmer Attachment

__ 1 - Operator's Manual
__ 1 - Safety Manual
__ 1 - Warranty Registration Card
__ 2 - Locking Tools
__ 1 - Wrench 17 x 14.5
__ 1 - Rapid Loader

TM

 Head

__ 1 - Nut
__ 1 - Washer 10x32x1.2
__ 1 - Plastic Debris Shield
__ 1 - Split Pin
__ 1 - Shield plate
__ 3 - 5mm x 16mm Screws (shield mounting)
__ 1 - Storage Hook Assembly

A

SSEMBLY

WARNING  

  DANGER

Do not perform maintenance or assembly procedures with engine
running.

Tools Required: Screwdriver, Head Locking Tool, 17x14.5mm Wrench,

Needle Nose Pliers

Parts Required: Power Head Shaft, Attachment Lower Shaft

Assembly, Plastic Shield, Shield Plate, three (3)
5mm x 16mm screws, Rapid Loader

TM 

 Head

POWER

 

HEAD

 

SHAFT

/

ATTACHMENT

 

LOWER

 

SHAFT

 

ASSEMBLY

1.

Set Power Head/Shaft Assembly on a level surface.

2.

Pull locator pin (A) and rotate counter clockwise 1/4 turn to lock
out position.

3.

Remove vinyl cap from attachment drive shaft.

4.

Remove cardboard spacer, if necessary.

5.

Carefully fit attachment lower drive shaft assembly into coupler (B)
to decal assembly line (C), making sure that the inner lower drive
shaft engages into the upper drive shaft mount.

A

B

D

Содержание PAS-260/261

















Отзывы: