Echo BEAR CAT SC5720B Скачать руководство пользователя страница 8

Страница: 8 / 30

5 INCH CHIPPER/SHREDDER/BLOWER

SAFETY

1.8 SAFETY DECALS

PN 12175

PN 12169

PN 12172

PN 12174

PN 12250

PN 12176

PN 12173

PN 14942-00

PN 32109-00

PN 32156-00

See Section 1.9 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine

and the associated hazards. See the engine owner’s manual or contact the engine manufacturer for engine safety

instructions and decals. Make certain that all safety and operational decals on this machine are kept clean and in good

condition. Decals that need replacement must be applied to their original locations.

KEEP HANDS AND FEET OUT OF INLET AND

DISCHARGE OPENINGS WHILE MACHINE IS

OPERATING TO AVOID SERIOUS PERSONAL

INJURY. STOP AND ALLOW MACHINE TO

COME TO A COMPLETE STOP BEFORE

CLEARING OBSTRUCTIONS.

KEEP HANDS AND FEET OUT OF

INLET AND DISCHARGE OPENINGS

WHILE MACHINE IS OPERATING

TO AVOID SERIOUS PERSONAL

INJURY. STOP AND ALLOW MACHINE TO COME TO A

COMPLETE STOP BEFORE CLEARING OBSTRUCTIONS.

CHECK

BLADE

BOLTS

FOR

PROPER

TORQUE

AFTER EVERY 8 HOURS OF

OPERATION. CHECK BLADES

AND ROTATE OR RESHARPEN

DAILY OR AS REQUIRED TO KEEP BLADES SHARP. REFER

TO OWNERS MANUAL FOR INSTRUCTIONS. FAILURE

TO DO SO MAY CAUSE POOR PERFORMANCE, DAMAGE

OR PERSONAL INJURY AND WILL VOID THE MACHINE

WARRANTY.

CAREFULLY READ THE

USER MANUAL BEFORE

'ACTIVATION. IF THE

USER MANUAL WAS NOT

INCLUDED WITH ANY

QUESTIONS OR CALL

+1-701-282-5520.

READ AND UNDERSTAND THIS

OWNER/OPERATORS MANUAL. BE

COMPLETELY FAMILIAR WITH THE

CONTROLS AND THE PROPER USE

OF THIS EQUIPMENT

OBTAIN AND WEAR SAFETY GLASSES

AND USE HEARING PROTECTION AT

ALL TIMES WHEN OPERATING THIS

MACHINE.

BEFORE INSPECTING OR SERVICING

ANY PART OF THIS MACHINE, SHUT

OFF POWER SOURCE, REMOVE THE

KEY, DISCONNECT SPARK PLUG WIRE FROM SPARK PLUG

AND MAKE SURE ALL MOVING PARTS HAVE COME TO A

COMPLETE STOP.

NOT

OPERATE

THIS

EQUIPMENT IN THE VICINITY OF

BYSTANDERS. DO NOT ALLOW

CHILDREN TO OPERATE THIS

EQUIPMENT. ALWAYS STAND

CLEAR OF DISCHARGE AREA

WHEN OPERATING THIS MACHINE.

KEEP FACE AND BODY AWAY FROM DISCHARGE AREAS.

DO NOT OPERATE MACHINE

WITHOUT SHIELDS IN PLACE.

FAILURE TO DO SO MAY CAUSE

SERIOUS INJURY OR DEATH.

DO NOT INSERT BRANCHES

LARGER THAN 3/4 INCH INTO

SHREDDER OR MACHINE

DAMAGE MAY OCCUR.

NOT

OPERATE

THIS

EQUIPMENT IN THE VICINITY

OF BYSTANDERS. DO NOT

ALLOW CHILDREN TO OPERATE

THIS EQUIPMENT. ALWAYS

STAND CLEAR OF DISCHARGE

AREA WHEN OPERATING THIS

MACHINE. KEEP FACE AND BODY

AWAY FROM DISCHARGE AREAS.

ROTATE THE DISCHARGE TUBE OVER THE HITCH

BEFORE TOWING AND LOCK SECURELY IN PLACE.

5.30-12

550 kPa, 80 psi

Содержание BEAR CAT SC5720B































Результаты поиска

Содержание BEAR CAT SC5720B

Отзывы:

Похожие инструкции для BEAR CAT SC5720B

Бренды по названию

Популярные бренды

Echo BEAR CAT SC5720B, Руководство пользователя

Результаты поиска

Содержание BEAR CAT SC5720B

Отзывы:

Похожие инструкции для BEAR CAT SC5720B

Бренды по названию

Популярные бренды